What are the conditions to consider for glass film on the balcony?

In the case of balconies, it is necessary to consider the light transmission while insulating the heat. And if you put the film, you must choose it carefully. Don't be like me, I was greedy for cheap, and spent dozens of dollars a square to paste it, but it didn't work and killed people, so I looked for it again.

After comparison, the dragon film is good, and theirs was chosen later. The price of people is indeed a little higher in comparison, but the quality of people is real, and the film is not the effect of the quality of the film after it is pasted.

Reflectivity, light transmittance. It cannot affect the light transmittance of the balcony, so that the indoor light is too dark.

1. Do not move the glass within three days after the installation of the window glass film, because it may contain water (the water has not evaporated), so it is best not to move.

2. Within 15 days after the glass is pasted and touched, do not use water to clean the glass with film.

3. Do not use adhesive to fix any items on the glass of the film, nor can you paste self-adhesive and other decorations on the window film.

Fourth, the cleaning agent is sprayed slightly and evenly on the surface of the window film, and then gently dry the window film with a clean, soft cotton cloth or absorbent wiping cloth, the cotton cloth and the absorbent wipe cloth often need to be wrung out, and the pure rubbing alcohol contained in the cotton cloth absorbent wipe cloth will quickly dissolve huge stains and greasy fingerprints. If the stain is not washed, respray the cleaning solution, wipe the window film horizontally from top to bottom with a soft rubber wiper until dry, and dry the edges of the window film with a towel.

Fifth, due to the use of adhesive tape, even stickers or decals on the window film, the glue or adhesive left when these materials are clear, you can use a soft clean cotton cloth dipped in acetone to gently scrub the contaminated area, you can quickly and completely clear the adhesive remaining on the window film. A small amount of acetone does not damage the polyester film, but it immediately dissolves and completely evaporates the adhesive and most spray paints.

6. Do not use soft erasers, brushes, and sand grains.

The above are some of the places that need to be paid attention to in the maintenance of architectural glass film recommended by American dragon film experts of Shenzhen Longfuhua Company, and I hope that my DIY friends will pay attention to it.

A reference guide for the purchase of a bucket of gold architectural film.

1.Facing east. Since the sun shines on the east side from 7 a.m. to 11 a.m., the time is short, you can choose a glass film with a moderate insulation rate (30-50%) to ensure that the temperature of the east room is moderate.

2.South-facing. Since the sun shines on the south side from about 9 a.m. to 16 p.m., which is a long time, you can choose a glass film with higher thermal insulation efficiency (about 50-70%) to ensure that the south room maintains a constant temperature, and at the same time improve the privacy of the south-facing bedroom living room, you can choose to use a one-way perspective film.

3.West-facing. Since the sun irradiation time in the west is about 13 o'clock in the afternoon - 19 o'clock in the afternoon, although the time is not long, but in the hot summer, the solar heat energy after noon is the highest, and the west room is the hottest, and the indoor temperature may be kept at the same maximum temperature from about 13 o'clock to 20 o'clock, so the west side should choose the glass film with the highest thermal insulation rate (about 70-80%) to ensure the efficiency of the air conditioner in summer.

4.Facing north. Since the north side is basically not exposed to the sun, the interior is cold and damp, and the wind in the north is more obvious in winter, so the north side should choose a glass film with a high thermal insulation rate (about 50-80%) to prevent heat loss in the cold season.

5.The first point is used for buildings with a plate structure, and the first point is applied to buildings with a point structure. It is required that the window film is installed on the outer glass of the building, so as to achieve the ideal energy-saving effect, and the glass film of different colors and styles can be installed in different directions to change the visual effect of the living room.

6.For buildings with more than 6 floors, the higher the floor, the higher the insulation rate, the glass film should be selected to ensure that each floor can reach the same temperature.

7.In the glass of the kitchen, dining room and bathroom, you can choose different colors and different styles of membranes (according to the customer's preferences) to beautify the living environment and improve the taste of life.

8.Users on the first to third floors (residential or commercial) are prone to theft, and pedestrians can see the interior, so they can choose an explosion-proof film (especially for shops) with a one-way perspective function.

9.Colored and colorless films:

The colored film is to turn the white light of the sun into colored light into the room, so that the light that people see is colored, very warm, romantic, soft and not dazzling, change the visual effect of the living room, and improve the interest of life, quality of life, and taste of life.

The questions to consider are:1...What kind of effect do you want from the customer?

2.The size of the balcony, the specifications.

3.The balcony is facing, and the backlight is still towards the light.

If it is a single transparent and reflective one, you must first seek the advice of the property to avoid trouble.

In fact, there is not much consideration, that is, you decide for yourself, you want good privacy, the color of the film is darker, and the thermal insulation rate is better.

If you want to have good light transmittance, you naturally have to use natural colors.

You can find a professional film company to serve you, you don't need to know everything!

1. Do not move the glass within three days after the installation of the window glass film, because it may contain water (the water has not yet evaporated), so it is best not to move. 2. Within 15 days after the glass is pasted and touched, do not use water to clean the glass with film. 3. Do not use adhesive to fix any items on the glass of the film, nor can you paste self-adhesive and other decorations on the window film.

Fourth, the cleaning agent is sprayed slightly and evenly on the surface of the window film, and then gently dry the window film with a clean, soft cotton cloth or absorbent wiping cloth, the cotton cloth and the absorbent wipe cloth often need to be wrung out, and the pure rubbing alcohol contained in the cotton cloth absorbent wipe cloth will quickly dissolve huge stains and greasy fingerprints. If the stain is not washed, respray the cleaning solution, wipe the window film horizontally from top to bottom with a soft rubber wiper until dry, and dry the edges of the window film with a towel. Fifth, due to the use of adhesive tape, even stickers or decals on the window film, the glue or sticky glue left when these materials are clear, you can use a soft clean cotton cloth dipped in acetone to gently scrub the contaminated area, you can quickly and completely clear the adhesive remaining on the window film.

A small amount of acetone does not damage the polyester film, but it immediately dissolves and completely evaporates the adhesive and most spray paints. 6. Do not use soft erasers, brushes, and sand grains.