-
Anonymous users2024-01-24I have a method, I have personally done it on the stainless steel water supply pipe, the simplest, most trouble-free and the best effect, oh, the technology, oh hehe.
The water supply pipe can be done well, and your sewer pipe is no problem, the main material, liquid raw meal glue (the best effect with this, if not, use glass glue), marble glue (that is, the commonly used glue for hanging stone), the method is as follows.
First, knock off the rust around the cracked iron pipe, and then polish it with sandpaper, and polish it slightly
Second, there can be no water flowing out of the cracked pipe, the water around the cracked pipe is dry, it is best to dry it with a blow blow, squeeze the liquid raw meal rubber from the crack to the inside, the amount of squeezing should be controlled, according to the size of the crack, squeeze into it and protrude some inside, it's good, the crack mouth and the outer glue are hit until the crack can not be seen, that is, the crack is flattened.
Third, if the seam is small, wait for the raw material glue to dry for more than ten minutes (if the glass glue is dried for a longer time), and then wipe the adjusted marble glue around the cracks, wipe thicker, and it is best to wrap the section of pipe with cracks, which is fine.
Marble glue when you use it and then adjust, because it will be hard after a while, so it is best to use it immediately after adjustment, you buy your own materials to try this method, it must be no problem, and there will be no problem after you do it well.
-
Anonymous users2024-01-23Smear the sand hole with glass water (bought in the building materials store) and sprinkle dry cement, then apply a layer of glass water and sprinkle a layer of dry cement. If the sand hole is small, it is glued with tape, there is a kind of aluminum-platinum tape, it is good to tear the piece and stick it, this kind of tape can also stick to the iron basin or something, it has to be sold everywhere, not afraid of water.
-
Anonymous users2024-01-22Stick marble to 502 glue can be glued, go to the stone market to buy some.
-
Anonymous users2024-01-21In this case, it is best to replace it, and there is a way to do it temporarily, and add me q to tell you.
-
Anonymous users2024-01-20I don't know if the glass glue will work, and I don't know if it will work after sealing it and drying it all.
Clean the black areas thoroughly, using a cleaner such as Toilet Cleaner and Vermeer if necessary. Observe if there is improvement after cleaning. If not, carefully observe whether there are cracks in the pipe. Symptomatic repair.
It may be the original leakage of the sewer pipe.
With a napkin, wipe it at the interface to see if there are any tide marks. >>>More
1. External treatment: Seal the toilet around, the water can't get in, and it won't seep out. >>>More
Upstairs down leakage problem is more difficult to find, to see the location of the leakage, the speed of leakage, in the upstairs drainage, water supply (hot water) pipeline, upstairs when the use of water downstairs is serious leakage and other comprehensive analysis, the basis for excluding the leakage of the tap water pipeline is the pipeline pressure, (can keep the pressure for 4 hours with pressure drop) is basically qualified, the surface of the embedded pipeline leakage wall should have traces of moisture, check whether the drainage equipment is smooth when draining, If there is a main water trunk line at the leakage location, it is not excluded that the main line and the middle of the floor slab leak, it is currently the wet season, and the water pipeline will not have good thermal insulation, and there will be condensation.
Choose to brush anti-rust paint, in the brush of a bitumen, reason, cast iron pipe has been embroidered, directly brush bitumen, the surface is not clean brush can not be brushed, first the rusty piece with sand to knock off, brush anti-embroidery paint again, dry, in the brush bitumen again, bitumen function is mainly waterproof, and anti-embroidery paint is mainly anti-embroidery.