How to install and remove the faucet of the kitchen sink, and how should it be installed?

The faucet of the kitchen sink is sometimes damaged due to too long use time or quality problems62616964757a686964616fe78988e69d8331333431373934,At this time, you must master the disassembly skills and installation skills of the faucet.

The first thing to do is to remove the faucet. Prepare the tools first, there will generally be screwdrivers, pliers and wrenches and the like, if there is a toolbox at home, it would be better, and then remember to close the main valve when dismantling, otherwise it will be a soup chicken. Next, you have to find out the position of the screws, and then unscrew them one by one, remember to put the screws unscrewed together, otherwise it is likely to be lost, and note that some of the screws are under the plastic sheet.

Then proceed to remove the handle on the top of the faucet. Some faucets will show signs of rust if they are used for too long, and it will be difficult to unscrew the screws at this time, so don't use brute force when screwing, it is easy to hurt yourself, and you can just drop some lubricating oil. If there are screws in the hole, use a flashlight to see if the screws inside are cross or slotted, which is more convenient and fast, and finally use a large wrench to remove the nut.

The next step is to install the faucet. Now it is basically a hot and cold alternating faucet, first fix the copper buckle and rubber pad in the two hoses, then connect the two hoses to the hole of the sink, and then fix it and then connect the faucet, remember to screw the copper wire, and then check the other places, and then connect the water outlet directly to make sure that there is no problem. One thing to pay attention to is that you must remember which hose you connect to is hot water and which is cold water, otherwise it will be very troublesome to use at that time.

Close the sluice, use a wrench to remove the faucet, put the hose into the connector and glue it, and then use screws to lock it.

Disassembly: Turn off the main sluice, then use a wrench to separate the inlet pipe and hose, remove the fixing parts of the faucet, and remove the water faucet.

Head. Installation: Extend the hose into the inside of the faucet, connect it, then connect the screw rod to the faucet interface, put the rubber ring on the faucet, then extend the faucet into the basin, add the rubber pad and gasket, and finally fix the screw with a wrench.

First of all, close the main valve, 62616964757a686964616fe4b893e5b19e31333431373934 tighten the valve of cold and hot water with pliers to avoid water leakage during installation. Then warp the sealant next to the sink and set it aside, and then you can change it.

Drain the remaining water from the faucet and keep the old towel next to it to prevent the water from running around after the faucet is removed. Use a fruit knife to gently pry the protective piece on the handle. This is usually put on or glued.

Remove the thin, flat protective sheet, like a button.

First, use a screwdriver to unscrew the screws that hold the handle in place, and then remove the handle. The handle engages with the longitudinal tooth profile and can be pulled out directly with very little force. Unscrew with a small wrench or pliers, then remove the spindle.

This is the shaft of rotation that has been removed. The red one is the rubber gasket. Swap it out.

The small porcelain piece under the gasket is placed on the left side under the gasket and on the right side above the gasket. The front and rear sides cannot be reversed, otherwise the water cannot be turned off. After installation, drain the water once and check whether there are leaks in all joints and whether the faucet is working properly.

No matter where the faucet is used, after a while, there will be some stains on the outside. A faucet with a good material will return to its original shiny surface after cleaning, while a faucet with a bad material will not be cleaned cleanly, resulting in a lot of stains on the surface. Therefore, it is advisable to choose electroplated faucets.

The faucet is scratch-resistant, corrosion-resistant, and the surface is not sticky, as new as new, extending the service life.

The material of the kitchen faucet is very important, after all, the water that comes out here is used for washing vegetables and cooking. Some of the toxic substances emitted when using inferior materials are very harmful to us。The kitchen faucet is recommended to be pure copper, which does not add other substances and does not emit harmful substances to the human body, which is more reassuring.

Another key factor in choosing a sink faucet is the accessories. The quality of the sink faucet is directly related to the cost of future maintenance. The tightness and corrosion resistance of the sewage pipe are the main factors that determine whether there will be water leaks in the future

Whether the water outlet has steel ball positioning, extrusion seal, table-controlled water removal, overflow device, silencing series device, etc. are all standards to measure the quality of accessories, and special attention should be paid to selection.

1.The sink must have a basket to prevent blocking the water and to facilitate cleaning. 2.The sink must be made to make an S bend, otherwise it will return to the taste. 3.sink.

The faucet handle must be large, easy to clean, and it is best to use the kind that can be pushed by the arm. 4.The sink countertop is easier to take care of the countertop, especially the stainless steel sink to the stainless steel countertop, the adhesive is much worse than that of artificial stone.

First turn off the water valve, remove the faucet, and finally install a new one.

Just follow the steps directly, remove the hose, and then remove the faucet, and install it in turn when installing, and pay attention to turn off the sluice.

First of all, you have to turn off the sluice gate of the whole house, and then divide the water pipe and hose for installation.

Turn off the faucet main gate first, and then the faucet interface should be selected to the general size to be installed.