What to do if the bathroom tiles keep falling

If only the tile falls off and the mortar remains on the wall and the ground is not loose, the solution is to scrape the remaining mortar on the back and side of the tile, and then apply an even layer of mortar on the back of the tile and press it back into place. If the mortar and the tile fall together, the solution is to first dig some pits on the wall and ground foundation, then layer mortar on the foundation surface, and then press the tile up until the tile is fixed on it.

Tile falling off is generally because of the laying with ordinary cement mortar to bond, the cement mortar has a relatively low cohesion and is particularly susceptible to environmental factors, often there will be tile hollowing or even falling off. If such a phenomenon occurs, it is best to switch to tile adhesive with strong adhesion and waterproofness. The special tile adhesive is not affected by the environment, it is very practical and inexpensive.

How to repair cracked tiles.

Tile paste can repair obvious cracks, which can be bought in the general large building materials market, tell the merchant the cracking condition of your home, and he will know what to give you. Tile paste is mainly used after hooking, it can produce a visual effect that is almost the same as the surface of porcelain, and it is hard and wear-resistant, and it is generally used by customers with high decoration standards. Tile paste is available in a variety of colors, with prices varying by brand and net content.

First of all, Note 1Before paving, you should deal with the smoothness of the wall, I don't know if there are cracks on the wall of your home, if there are, you must deal with the cracks first. 2.

The adhesive material should be applied slightly higher than the middle of the four sides, and I think there may not be such a thing if I make it myself at home, but if I really can't do it, press it with my hand to prevent air from accumulating in the adhesive layer. 3.The bonding material should be properly reconciled, and the ratio of cement to sand on the wall is generally 1:

4。 4.Because replacing the porcelain tiles usually destroys the waterproof layer of the original cement sand paddle.

The remedy is to apply a layer of asphalt waterproofing before the tiles are applied. The joints between the tiles should also be filled with white cement. Let me talk about the specific construction method.

First, the plane is swept and moistened, and the base is made with 1:3 cement mortar, with a thickness of 6 mm. The walls should be slightly hairy, but they must be flat.

After the priming, start pasting the tiles every 3 to 4 days. When tiling the tiles, you should first water the wet wall, and place the ruler board at the bottom of the bottom layer of tiles, which must be kept horizontal, and it must be fixed. The tiles should be pre-soaked in water, take out a little shade dry, and stick them along the board from the ruler board.

Adding an appropriate amount of 3 4 107 glue to 1:2 cement fine sand can improve the workability of the mortar. Slows down the setting time.

to facilitate the pasting and prevent the mortar from flowing. Spread the mortar on the back of the tile, stick it on the wall and tap the brick surface with a rubber hammer to fill the mortar. The seams are dried with white cement.

Paste tiles on the cement mortar plastered wall and paste them with cement slurry mixed with 5 7 107 glue. If the wall is very flat, sweep it with pure cement grout first, and start pasting it when it is not dry. Because the adhesive layer is not mixed with sand, it is very thin, only 2 3 mm thick, and it is easy to smooth when bonding, so this is a very convenient and economical method.

Always drop one piece, or something else, I suggest you use more cement to strengthen the proportion of sand and cement so that it will not fall, and you can also find a professional to help you stick.

Workers are too irresponsible during construction! They did not responsibly check whether the back of the tile was completely combined with the cement during construction, or the cement label was not purchased in accordance with the standard, resulting in the tile falling off after the cement dried.

If there are not many tiles that have fallen, you can use glass glue or marble glue to re-paste them on the wall, but it will not work for a long time. Or find a professional to help you glue with cement.

With tile adhesive can be perfectly attached to the tile, not afraid of falling, high stability, only sand cement is unstable, easy to fall off.

Cement and less of it, or it is recommended to try a different tile.

Brush dispensing 801 before sticking the bricks