What are the bathroom floor practices?

Be sure to do wall waterproofing, before laying wall tiles, do a good job of wall waterproofing. Generally, the wall should be waterproof with a height of 30 cm, but for non-load-bearing light walls, the whole wall should be waterproofed, at least 60 cm high.

The joints between the wall and the ground and the joints of the pipes between the water and the water are the most problem-prone places, and the workers must be urged to deal with these edges and corners, and the waterproof coating must be applied in place.

If you need to replace the original floor tiles in the bathroom, after chiseling off the original floor tiles, you must first level the ground with cement mortar, and then do waterproof treatment, so as to avoid leakage caused by uneven thickness of the waterproof coating. Be sure to clean the ground before doing waterproofing.

Try not to damage the original waterproof layer, the ground of the newly delivered building is generally made of waterproof layer, so there is no leakage without destroying the original waterproof layer.

The decoration team is required to make cement mulch for the upper and lower water pipes of the bathroom, brush 10 to 20 cm of waterproof paint from the ground, and then redo the ester waterproof on the ground, add the original waterproof layer, and form a composite waterproof layer to enhance the waterproofness.

The groove of the water pipe in the wall should also be waterproof, and the waterproof layer around the hole must be carefully constructed when the pipe, floor drain, etc. pass through the floor slab during the construction process. Buried water pipes in the wall, so as to achieve a reasonable layout, lay water pipes are made of grooves larger than the pipe diameter, plastering in the groove is smooth, and then brush waterproof paint in the groove.

With 24 hours of "water storage test" acceptance waterproofing, after the completion of the waterproof project, seal the door and drain, fill the bathroom floor with water to reach a certain liquid level height, and make a mark, if the liquid level does not drop significantly within 24 hours, especially the roof of the downstairs house does not leak, the waterproof is qualified.

1.Edge banding cross positioning frame.

The use of these auxiliary materials has greatly improved the construction technology of yin and yang corners in the pavement, and there is no longer a need for 45 degree trimming of ceramic tiles, which greatly saves man-hours and damage. Cross positioning can improve the joint accuracy of floor tile paving and simplify the construction process.

2.Combination pavement of various specifications.

It is characterized by the selection of a variety of floor tiles of different geometric sizes and sizes to be paved in groups according to a certain combination. Because the floor tiles are combined by different sizes, and there are many combinations, the geometric lines of the ground change immediately, reflecting the change and vividness in the order.

3. Dry paste method. The use of tile adhesive pavement is also called dry pasting, which changes the wet practice of mortar cement, and the tile does not need to be soaked in water in advance, and the base surface does not need to be wet. As long as the basic conditions of the pavement are good, the operation condition can be greatly improved. Its bonding effect also exceeds that of traditional mortar cement, especially suitable for small and medium-sized projects and home decoration with a small working surface and an unsatisfactory working environment.

4 Colorful caulk.

It is not an ordinary colored cement, and is generally used for seam paving floors or walls. It is characterized by strong color fixation, pressure resistance, wear resistance, no alkalization, no shrinkage, no chalking, not only to change the tile gap is easy to fall off and not firmly adhered to the problem, but also to make the color of the gap and the tile match appear unified and harmonious complement each other.

5. Wall paving.

The combination of 45-degree diagonal paving and vertical paving makes the wall surface rich and varied from the original monotonous geometric lines, enhancing the three-dimensional sense and lively atmosphere of the space.

6 Floor tiles are randomly combined with a variety of colors.

This is the latest paving trend in Spanish tiles, which is paved by a random combination of floor tiles with different glaze colors. The visuals vary widely. This is a challenge to our traditional aesthetic of "symmetry and unity". It is suitable for larger halls.

7. Leave seams and pavement.

Now the market is popular antique floor tiles, which mainly emphasize the return of history. The glaze is treated with uneven and uneven straight edges, and the necessary gaps left during paving are filled with colored cement, so that the overall effect is unified and emphasizes the dignified sense of history.

The solution once and for all is to re-lay the ground from scratch.

If you really don't want to get it, you can give you a way, you can cut the rubber of the right size and paste it on the corners with glass glue.

The glass glue is waterproof and can be fully adhered to glazed tiles.

Be careful not to wet the adhesive area until the glass glue has dried!