The wooden floor in the living room is bulging with a big bag, and the area of four or five floors i

First, the reason for the arching of the floor.

1. The reason for arching is because the floor is heated and expanded and contracted, and when the floor is installed before, the gap between the floor and the wall is not enough to be reserved, resulting in telescopic arching.

Second, the maintenance plan.

2. Remove the baseboard from the wall Remove the edge from the wall to the position of the arch and then re-pave all the long part to the wall side and leave the gap to install the baseboard The edge of the edge is completed.

3. Excipients required: a bottle of D3 glue and a bottle of glass glue.

1. Edge bulge.

An oval bulge appears on the edge of the floor panel, with a single bag appearing in the middle of the two floors, and a plurality of bags appearing in the middle of the two floors; Some are connected in a piece, showing an irregular distribution in the room.

2. The board surface is bulging.

Oval bags appear on the floor panels, with single or multiple bags appearing in the middle of the flooring at the same time, showing an irregular distribution in the room.

The causes of bulging are roughly as follows:

1) The ground is uneven or there are sand particles on the ground.

Before the installation of laminate flooring, because the ground is not cleaned, there are some small sand particles on the ground or the ground is too rough, after the installation of the floor, in the process of people stepping on it, the moisture-proof film and the balance layer on the back of the floor are destroyed, and the moisture of the ground causes the floor to bulge.

2) Improper handling of moisture-proof measures.

This type of situation is an improper moisture-proof treatment during installation. On damp floors, if the moisture-proof membrane joints are not tightly glued with waterproof tape, even if the balance layer on the back of the floor is not damaged, the floor is in a humid environment for a long time, and the moisture may still enter the floor after the balance layer is eroded by moisture, causing damage to the floor.

3) Improper use:

The bulging phenomenon caused by water ingress at the floor joints (such as: heating running water, large area of water ingress, etc.) belongs to the problem of improper use and maintenance by users.

3.Care Recommendations:

Compared with other wood flooring categories, laminate flooring is not particularly delicate, and daily maintenance can extend the service life of laminate flooring and avoid some problems as long as you pay a little attention to it. In view of the bulging phenomenon, in addition to product quality factors, the indoor ground in daily life can not be flooded in a large area, and the windows should be closed at any time when the rainy season comes, so as to avoid being wet by rain; When cleaning, try to use a vacuum cleaner or semi-dry mop to take care of it, do not use a dripping mop to mop the floor, if you accidentally spill water on the surface of the laminate floor, immediately wipe off the water with a dry cloth to prevent water from leaking from the floor joints.

It is arched, the arching of the floor is mainly caused by moisture, and there is no other way to replace it after arching, but you must be careful in the future, in case there is water dripping, you must dry it in time and let it dry completely, do not let the sun shine directly or use a hair dryer to dry.

Hello friends, I am Zhangmu Floor Maintenance. It's not uncommon for you to be in a situation like this. It needs to be dismantled and re-paved. It's not very troublesome either. Otherwise, it will be more serious in the future. In the end, the floor will be overturned.

It should be that it is not paved when decorating After all, it is necessary to leave seams Because the floor is also to expand and shrink Now that it has been arched, it is recommended that LZ redecorate it Don't feel distressed Oh If you re-pave, buy the same floor material may not be the same It is not good-looking And can you guarantee that similar things will not happen elsewhere It is recommended that you renovate it Pay attention to moisture-proof [Ground moisture-proof treatment method: generally use "three oil and two felt" (three layers of asphalt and two layers of linoleum paper, and then smear a layer of cement on it to prevent the release of harmful gases); The simple treatment method is to lay a layer of moisture-proof film, moisture-proof paper, moisture-proof ah, bigger.

Generally, the floor is to leave expansion joints to prevent the floor from expanding after thermal expansion and cold contraction, if you don't want to re-splice all the paintings, call a carpenter to take a cutting machine to cut out a seam at the edge position.

I know there's no crack, I'm in this business, it's not uncommon for this to happen, and it can be alleviated a little bit according to my method. As long as there is a seam that is enough for it to expand and contract, it does not need to be very large, and the carpenters know it.

It swelled when it met the water.

You can ventilate and see the results again.

If the planks are already cracked.

Then you have to change.

!!!If it is due to water ingress into the floor, then the joint along the edge of the floor will bulge first, LZ can see the joint of the raised floor, in which case you can only contact the dealer to replace it.

If it is due to the expansion joint is not left enough, that is, the floor of the whole room will form a whole bulge, and the place where there is no heavy object will be relatively more obvious, if it is not very serious, you can move a heavy object to flatten, and then the heavy object will be half open for a while, if it is serious, please ask the installer to remove the baseboard, cut off the floor part that has been against the wall, and then find a heavy object to press on the bulge part for about two days.

If you get wet or have a problem with the flooring material, contact your dealer immediately.