What to do if there is a leak in the bathroom? How to deal with it

1. Try not to damage the original waterproof layer: If the original waterproof layer is not damaged, there will generally be no leakage after moving in. However, the waterproof layer is easy to be damaged when renovating the ground, and if it is accidentally damaged, it should be repaired in time to avoid leaving hidden dangers.

Second, the resurfacing floor tiles should be waterproofed: If you need to replace the original floor tiles in the bathroom, after chiseling off the original floor tiles, you must first level the ground with cement mortar, and then do waterproof treatment. Repeat 2 to 3 times with polyurethane waterproof paint.

3. Be sure to do wall waterproofing: Water will splash on the adjacent wall when bathing in the bathroom, so be sure to do a good job of wall waterproofing before laying wall tiles. Generally, the wall should be waterproofed with a height of 30 cm in waterproofing treatment, but for non-load-bearing light walls, the entire wall should be waterproofed, at least meter high.

At the same time, pay attention to the waterproofing of the wall adjacent to the shower position should also be meters high. Fourth, the groove of the water pipe in the wall should also be waterproof: During the construction process, when the pipe, floor drain, etc. pass through the floor slab, the waterproof layer around the hole must be carefully constructed.

The buried water pipe in the wall should be reasonably arranged, and the water pipe should be made with a groove larger than the pipe diameter, and the plastering in the groove should be smooth, and then the groove should be brushed with polyurethane waterproof coating. Fifth, 24-hour "closed water test" acceptance waterproofing: After the waterproof project is completed, seal the door and the drain, fill the bathroom ground with water to reach a certain liquid level height, and make a mark, if the liquid level does not drop significantly within 24 hours, especially the roof of the downstairs house does not leak, the waterproof is qualified.

There are generally two types of bathroom leaks:

1. The waterproofing is not done well, resulting in water seepage on the ground;

2. Water leakage caused by damage to the upper and lower water pipes.

How to judge the cause of water leakage in the bathroom.

1. As long as the ground uses water, there is water leakage downstairs, and when the ground does not use water, there is no more water leakage downstairs. This is the case of water seepage on the ground;

2. The leakage of general water pipes is large and continuous; If the bathroom has not used water for several days, but there is still water leakage, and the leakage water has not been reduced, it is a problem with the water pipe.

Toilet leak repair method.

1. If the bathroom is leaking water from the waterproof layer, not the upper and lower water pipes. They can be repaired without planing tiles. The maintenance method is very simple, which is to use a new type of penetrating waterproofing agent to waterproof the surface of the bathroom, so that the water does not enter the ground and flows directly from the waterway.

Second, if it is a problem with the upper and lower water pipes. And if the water pipes are underground, you need to consider planing tiles, but you don't have to redecorate the bathroom. For example, if the inlet pipe is leaking, the pipe can be changed to avoid the leaking water pipe.

If it is a leak in the sewer pipe, it is also necessary to find the specific location of the leakage, and according to the situation, it is determined that it is partially planed bricks to solve, and it is not necessary to plane all of them.

As long as you find out the location and cause of the leakage in the toilet and repair it in time, you can keep the safety and comfort of your home.

There are generally two types of water leaks:

First, the pipe rupture leads to water leakage, which needs to be replaced and re-waterproofed.

Second, the waterproofing is not done well, resulting in water leakage, and the overall waterproofing needs to be redone.

It is recommended to find a renovation worker to find the leakage point (around the water pipe, the corner of the wall is an area prone to water leakage), and then re-waterproof the water leakage.

Don't blindly repair the toilet leakage, first find out the cause of the leakage, in order to deal with it correctly. There are only two reasons for water leakage in the bathroom, the first is water seepage on the ground, and the second is water seepage from the broken upper and lower water pipes. Don't know what kind of person you are??

The treatment of water leakage in the bathroom can not be blindly repaired, and the cause of the leakage must be clarified before it can be dealt with correctly.

Before repairing the toilet leakage, it is necessary to determine the cause of the toilet leakage, and the two methods for judging the causes of water leakage are as follows:

1. The method of judging the water seepage on the ground: as long as the ground uses water, there is water leakage downstairs, and when the ground does not use water, there is no more water leakage downstairs.

2. The method of judging the leakage of water pipes: the leakage of water pipes is large and continuous; If the bathroom has not used water for several days, but there is still water leakage, and the leakage water has not been reduced, it is a problem with the water pipe.

How to deal with toilet leakage:

1. If the bathroom is leaking water from the waterproof layer, not from the upper and lower water pipes. They can be repaired without planing tiles.

The maintenance method is very simple, which is to use a new type of penetrating waterproofing agent to waterproof the surface of the bathroom, so that the water does not enter the ground and flows directly from the waterway. You can go to the Internet to find 100 million waterproof. Learn more details.

2. If it is a problem with the upper and lower water pipes. And if the water pipes are underground, you need to consider planing tiles, but you don't have to redecorate the bathroom. For example, if the inlet pipe is leaking, the pipe can be changed to avoid the leaking water pipe.

If it is a leak in the sewer pipe, it is also necessary to find the specific location of the leakage, and according to the situation, it is determined that it is partially planed bricks to solve, and it is not necessary to plane all of them.

How to judge the cause of water leakage in the bathroom.

Before repairing the toilet leakage, it is necessary to determine the cause of the toilet leakage, and the two methods for judging the causes of water leakage are as follows:

: The method of judging the water seepage on the ground: as long as the ground uses water, there is a phenomenon of water leakage downstairs, and when the ground does not use water, there is no longer water leakage downstairs.

: The method of judging the leakage of water pipes: the amount of leakage from water pipes is large and continuous; If the bathroom has not used water for several days, but there is still water leakage, and the leakage water has not been reduced, it is a problem with the water pipe.

1. If the bathroom is leaking water from the waterproof layer, not the upper and lower water pipes. They can be repaired without planing tiles.

The maintenance method is very simple, which is to use a new type of penetrating waterproofing agent to waterproof the surface of the bathroom, so that the water does not enter the ground and flows directly from the waterway. You can go to the Internet to find 100 million waterproof. Learn more details.

Second, if it is a problem with the upper and lower water pipes. And if the water pipes are underground, you need to consider planing tiles, but you don't have to redecorate the bathroom. For example, if the inlet pipe is leaking, the pipe can be changed to avoid the leaking water pipe.

If it is a leak in the sewer pipe, it is also necessary to find the specific location of the leakage, and according to the situation, it is determined that it is partially planed bricks to solve, and it is not necessary to plane all of them.

Here's how to solve the problem:

1. Treat the dust, oil, and stagnant water on the surface, and keep the surface dry.

2. If the tile joint is filled with caulk, you need to use a knife to draw a small groove; 3. In the cement parts such as tile surface, tile joint, wall joint, pipe root, etc., spray permeable waterproofing agent, and be sure to spray evenly; 4. After the waterproofing agent 9 is dry (about 2 hours later), fill all tile joints and damaged and defective parts with caulking paste, and the weak links around the pipe root are reinforced; 5. The connection between the ground and the wall and the pipe root are made of plastic steel mud as a waterproof edge; 6. After the waterproof construction is completed, the construction site cannot be drenched with water within 24 hours.

As long as you find out the location and cause of the leakage in the toilet and repair it in time, you can keep the safety and comfort of your home.

Contact the upstairs homeowner and the property management company first, and go to the upstairs homeowner to check the situation on the spot.

First of all, close the water valve as much as possible to avoid further leakage. Check the leakage points one by one, you can first put the gap between the heating pipe and the casing, the sewer pipe, the floor drain, and the root of the wall are all easy to leak locations, and in the case of cleaning and drying, evenly apply glass glue to seal it. Then use a seam or waterproof glue to coat and seal the gaps between the tiles.

Do not use water for 24 hours. Test the water after 24 hours. Secondly, you can drill multiple small holes at the water seepage on the top surface of your home according to different positions, and then use a syringe to drive the waterproof paint into the holes.

The expansion of the waterproof coating blocks the internal gaps, and then achieves the effect of waterproofing. This is a simple grouting waterproofing treatment. After the above treatment, the general leakage situation can be solved.

How to deal with toilet leakage and how to repair it.

1. If the upper and lower pipes are broken, the pipes should be replaced.

2. If there is water seepage on the ground, please follow the steps below to fix the toilet leak.

1. Clean dust, oil stains and stagnant water on the surface, and keep the surface dry.

2. If the tile joints are filled with caulk, you need to use a knife to cut a small groove.

3. Spray penetrating waterproofing agent on the surface of the tile, tile joints, wall joints and pipe roots, and ensure uniform spraying.

4. After the waterproofing agent is 90% dry (about 2 hours later), fill all tile joints and damaged parts with seam sealant.

5. After waterproof construction, the construction site shall not be wet with water within 24 hours.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

Bathroom leakage is the first thing to determine where the water leaks. Generally, there are three kinds of water leakage: 1. The leakage of the waterproof layer is manifested as serious water leakage downstairs after bathing or ground water, and the downstairs performance may be one or more places.

The judgment method is very simple, plug the floor drain, and then release water on the ground, pay attention to the observation of the water leakage downstairs after 40 minutes, if the water leakage downstairs is serious, it is determined that the waterproof layer is leaking. In this case, you can find some waterproofing on the Internet, use waterproofing agent, caulking paste, and plastic steel mud to repair. That is, the surface of the bathroom is waterproofed again, without planing tiles, saving time and cost.

2. The sewer pipe is leaking, which is manifested around the sewer pipe, and there is a serious dripping phenomenon. The way to judge is to drain the floor, the hand basin, fill the water, and repeatedly flush the toilet, and see the aggravation of the water leakage downstairs, it is the leakage of the sewer pipe. In this case, find a repairer to replace the sewer pipe and try to reduce the bricks as much as possible.

Then it also needs to be waterproofed under the ground rework, and there is no need to plane all the bricks. 3. That is, the water inlet pipe leaks, if the water leakage is uniform and continuous, turn off the upper water, and the water will be reduced and will not leak. It means that the water pipe is broken.

This situation can be solved by changing the open pipe, no need to plane the bricks, or judge the leakage point by suppression, and change the pipe is probably like this! Hope it helps! If you think my answer is good, you can give me a thumbs up! ~