The mouth of the sewage pipe is flush with the floor, so can I install a toilet? What are the implic

Can't come to install.

Before installing the smart horse source barrel, under normal circumstances, the decoration company reserves the sewage pipe 305mm or 400mm away from the wall. The diameter of the reserved sewage pipe hole is 100 (90mm-110mm), which is smaller or greater than this range and will cause the toilet to be unable to be installed.

The aperture is too small and needs to be reretrofitted. The aperture is too large, it can be modified directly on site, as shown in the figure below, the master inserts 1 to 2 circles of 100mm plastic pipe in the pipe diameter above 120mm, and fills in the sealing flange glue.

1. Check the leveling between the sewage pipe and the ground.

First, use a hacksaw to see the nozzle of the sewage pipe to the position off the ground, so that the flange ring can be closely attached to the nozzle when the flange ring is installed in the future to avoid water leakage. Before the toilet is installed, it is necessary to conduct a comprehensive inspection of the sewage pipe to see if there is any blockage of sediment and waste paper in the pipe, and to check whether the ground is level before and after the toilet installation location.

2. Determine the center of the sewage pipe.

Secondly, to determine the center of the sewage pipe, you can turn the toilet over, determine the center on the sewage outlet of the toilet bowl and draw a cross center line.

Shops that sell toilets sell special rubber seals for toilets. Like oil seals.

Now it's a one-piece toilet, and it's okay without an expansion screw. Plug those two holes.

The ground must be sealed.

You can make a flange first, put sealant around it, and then use that black sealing mud.

No problem, the upstairs are very good, pay attention to waterproofing!

Toilets are hard to find to screw these days!

Can be installed" recommends that you buy a toilet with straight drainage, as for the way there are too many, but none of them are too good.

When installing a toilet with a flange ring, the sewage pipe is sawed flat to the ground, and the maximum is less than 1CM. You can do this.

Yes, it doesn't have much impact!! It can be basically the same as the ground!!

Not a big problem, he has a kind of rubber seal that is connected between the toilet outlet and the drain.

The mouth of the sewage pipe is flush with the floor, so can I install a toilet? What are the implications?

Dear, hello, I am happy to serve you, the answer is as follows: The mouth of the toilet is flush with the ground, and the toilet can be installed. However, if you install it in this way and use the toilet later, there may be a sewage overflow.

It is not clear that when installing the toilet, it is necessary to play a circle of structural glue or glass glaze glue around the mouth of the sewer pipe, and the colloid height should not be less than one centimeter, and then place the toilet, so that when the toilet is used in the future, due to the barrier of the colloid, there will be no sewage overflow.

The mouth of the sewage pipe is flush with the floor, so can I install a toilet? What are the implications?

Kiss! Hello, happy to answer your <>

The sewer nozzle of the pro-toilet is flush with the ground, so it is possible to install the toilet. However, if you install it in this way, and use the toilet in the future, there may be a phenomenon of sewage overflowing. Therefore, when installing the toilet, it is necessary to put a circle of structural glue or glass glue around the mouth of the sewer pipe, and the height of the colloid should not be less than one centimeter, and then place the toilet, so that when the toilet is used in the future, due to the barrier of the colloid, there will be no sewage overflow.

What to do if the toilet drain and the floor are flat1Level the floor so that the lower drain pipe is slightly higher than the ground (you can first look at the height difference between the drain outlet of the new toilet and the lower edge). 2.

Place the toilet flange (a gummy circle) over the waterway pipe. 3.Press the toilet bowl against the flange from directly above.

4.Connect the water supply stub. When the toilet sewer pipe is installed, it can not be flush with the ground, if it is flush with the ground, the flange ring and sewer pipe of the toilet can not be well sealed, then when used in the future, there will be water leakage, aftertaste and other phenomena, I hope mine can help you <>

Do you have any other questions?

The mouth of the sewage pipe is flush with the floor, so can I install a toilet? What are the implications?

Kiss! Hello Tongran, I am happy to answer your <>

The sewer nozzle of the pro-toilet is flush with the ground, so it is possible to install the toilet. However, if the wheel is installed in this way, the toilet may overflow in the future. Therefore, when installing the toilet, it is necessary to put a circle of structural glue or glass glue around the mouth of the sewer pipe, and the height of the colloid should not be less than one centimeter, and then place the toilet, so that when the toilet is used in the future, due to the barrier of the colloid, there will be no sewage overflow.

At least two centimeters above the ground, otherwise it is easy to cause leakage of the toilet base, like this case, you must connect the sawn water pipe a few centimeters up. If it is flush with the ground, the flange ring and sewer pipe of the toilet can not be well sealed, and when it is used in the future, there will be water leakage, aftertaste and other phenomena, I hope I can help you <>

Do you have any other questions?