How to test the water after the bathroom is tiled

After the bathroom is tiled, it is better to use it for a long time. If the bathroom is ventilated, it can be used within two days. If there is no ventilation, it will be fine for a few days at most.

If you don't, it's pointless. The bond strength of ceramic tiles mainly depends on whether the material is dry or not, and the strength time of cement mortar is 72 h.

Therefore, domestic hot water is available after 24 hours of toilet decoration and tiling. Underneath the floor tiles is a mixture of cement and yellow sand, mainly yellow sand, with only a small amount of cement, and it is basically dry and does not need to wait long for it to cure. When laying floor tiles, after hammering with a rubber hammer, it is mixed with the yellow sand below, and the position cannot be moved well.

When laying bricks, the tile is well protected and does not scratch the brick surface and pollute the brick surface.

Walking on uneven brick surfaces, painting walls, not using protective films, etc., often occur during construction, which can cause damage to the tiles. After the bathroom is waterproofed, a test water test, also known as a closed water test, will be performed. In order to prevent floor leakage, the first thing to do is to pack the prepared sand in a plastic bag to strictly seal the floor leakage and prevent the loss of stored water.

Fill the door with cement with water. Get the water out. Water should soak the entire floor for a closed water test.

After 48 hours, check the results of the shut-off water experiment and go downstairs to carefully check for leaks. Of course, if the tile is posted by someone else, he will help you test the water, and the owner will test it himself, because the master here basically has no responsibility in the later stage. Therefore, it is recommended that you find a master to test the water, so as not to leak the water downstairs and be knocked on the door.

If you don't do it well, the downstairs will leak. You don't have to go out of your way to test the water, the downstairs will look for you if the water leaks.

After the bathroom is waterproofed, it is necessary to test the water, also known as the closed water test.

Step 1: Plug the floor drain.

First of all, put the prepared sand in a plastic bag to block the floor drain and prevent the stored water from running away.

Step 2: Plug the door with cement that is likely to be full of water.

Step 3: Drain the water. The entire ground of the closed water test should be soaked with water.

Step 4: After 48 hours, check the results of the closed water test and go downstairs to carefully check whether there is any leakage.

Hello, I'm glad to answer your confusion, in all areas of the home, the most contact with water is the bathroom, so waterproof to do a good job, so what are the specific steps of waterproof water test? Let's follow PChouse to find out.

1. Remove the original floor tiles and wall tiles.

Remove the original wall tiles and floor tiles, this step is generally for the second decoration of the old house, if it is a new house, then this step can be skipped, generally using a gray knife, the scraper can also remove the original floor tiles.

2. Plug the sewer pipe.

The waterproofing of the bathroom is usually carried out after the completion of water and electricity, so the sewer pipe must be blocked before doing waterproofing, the purpose of this is to avoid blockage, the small water pipe is blocked with a nut, and the large sewer pipe (such as the toilet sewer pipe) is blocked with PVC winding film.

3. Ground and wall leveling.

The leveling here is usually the ground plastering treatment, the ratio of mortar cement and sand is between 1:2-1:3, pay attention to the thickness of the leveling should not exceed 3cm. The horizontal and vertical errors should also be controlled within 5mm.

4. Make a waterproof layer.

First of all, the wall will be slotted with cement to clean up the base layer, the details of the additional layer construction, in the pipe root, floor drain, yin and yang corners, and other weak parts that are easy to leak evenly painted, painted waterproof paint twice, painted longitudinally and horizontally, but also remember to do a good job of protective layer, after waterproof drying, release water to do 48 hours of closed water test.

Ask the bathroom, waterproof and then toilet that has a nest to test waterproof.

First of all, the wall will be slotted with cement to clean up the base layer, the details of the additional layer construction, in the pipe root, floor drain, yin and yang corners, and other weak parts that are easy to leak evenly painted, painted waterproof paint twice, painted longitudinally and horizontally, but also remember to do a good job of protective layer, after waterproof drying, release water to do 48 hours of closed water test.

Before you don't have tiles, you have to test the water, usually after doing waterproofing, you have to put water to test whether there is any leakage.

Dear, it's already pasted how to test the waters. If you don't do it well, the downstairs will leak. You don't have to go out of your way to test the water, the water leaks and the downstairs will find you.