How to get rid of cement in the toilet potty

Cement removal method:

1. Apply oxalic acid and rub the steel wool ball after 10 minutes.

2. Soak the dry cement in water in advance, the cement will be soft after soaking in water, and it is easier to remove, so you can shovel it off directly with a shovel, and then wipe it with a steel wool ball.

3. With cement plant.

Laboratory use.

Dilute hydrochloric acid or. The dilute sulfuric acid is cleaned and it is off.

4. Available. Scrape off wood chips, sticks, etc., and clean them with a soft cloth.

5. Use cement dissolving agent.

agent for cleaning. Cement dissolving agent.

Home renovation. Cement blockage of sewers caused by carelessness; Urine alkali blockage formed by sanitary ware over time and other conditions that require dissolution of cement.

Extended Information: Precautions for Using Cement Dissolving Agents:

1. Do not touch the skin or mouth and eyes, and children should not approach!

2. After reacting with urine alkali, it will produce a certain odor, pay attention to the discharge and close the door.

3. Please use it in a well-ventilated environment.

4. No other chemical solvents should be used before and after use.

5. After not using up, tighten the cap and pay attention to moisture.

6. Invisible corrosion, rotten pipes should be used with caution.

7. The resolution cycle is relatively long, generally about 10 days to be resolved.

Therefore, it is necessary for the customer to wait. Non-immersion finish:

Due to the fact that the area that cannot be covered by the solution can not be effectively treated during the treatment process, it is necessary to brush it several times with a prepared plastic brush dipped in the solution after each dose. Urine alkali is also removed with this product.

Encyclopedia - Cement.

Scrub with diluted oxalic acid.

Don't forget to protect your hands and wear rubber gloves when scrubbing. Apply it with a brush to the area where there is cement, and wipe it off with a dry cloth after 3-5 minutes. If the surface is not a cement block but a stain of cement water, the grinding bureau can go to the supermarket to buy tile stain remover, and use it according to the instructions after buying it.

Note not to use hydrochloric acid, sulfuric acid, nitric acid, will seriously corrode the brick surface, do not use a shovel, it is also easy to shovel damage, the residual cement stains on the surface of the tile can be removed with the descaling king tile cleaner, which is specially removed from the residual cement on the surface of the tile, pour the solution, wait a few seconds, wipe it off, clean and clean, no negative effect on the surface of the tile.

Newly lived house, after the renovation of cement fell on the bedpan, how to remove the following methods:

1. If the solidified cement block falls into the sewer, it can only be slowly pulled out with a dredging machine or other small tools;

2. If the cement slurry that has not solidified falls into the sewer, rinse it with water immediately and flush it several times.

3. If the cement slurry falls on the toilet and has solidified on the toilet, you can only use a small shovel to shovel first, and then flush it with water a few times.

4. If the cement slurry is poured into the toilet or sewer and has solidified, no one has a good way but to dismantle it and replace it with a new one.

Hello, you can first find a sharp shovel to shovel off the cement, do not hurt the enamel, and then gently wipe it with 1500 or 2000 water sandpaper. It would be better to add some water when grinding. It can also be polished with an angle grinder, but the key is to grasp the strength.

2.It can be cleaned with oxalic acid (tile cleaner), and it is also important to scrub with diluted oxalic acid. However, be sure to rinse with water after wiping.

Don't forget to protect your hands and wear rubber gloves when scrubbing. Apply it to the cement area with a brush first, and wipe it off with a dry cloth after 3-5 minutes. The current mention is that you have enough confidence in your porcelain glaze.

You can go to the store to buy low-concentration hydrochloric acid, wipe it, and then rinse it with clean water to shovel the cement, preferably with a wooden shovel, which is not easy to damage the glaze.

Use the diluted oxalic acid shouted by Luqiao to scrub and eliminate noise. Don't forget to protect your hands and wear rubber gloves when scrubbing. Apply it with a brush to the area where there is cement, and wipe it off with a dry cloth after 3-5 minutes.

If the surface is not a cement block but a stain of cement water, you can go to the supermarket to buy a tile stain remover, and use it according to the instructions after buying it home.

Apply oxalic acid. After 10 minutes, the steel wool ball is ok to scrub

Oxalic acid can be used to remove rust. However, be careful when using, oxalic acid is highly corrosive to stainless steel.

Oxalic acid cleaner can be bought on Taobao.

Apply oxalic acid. After 10 minutes, the steel wool ball is ok to scrub

1.Clean it with dilute hydrochloric acid or dilute sulfuric acid used in the laboratory of the cement factory and it will be dropped! Because cement is alkaline, it melts or dissolves when exposed to acid. However, strong acids can damage the surface of the cement.

2.Clean with cement cleaner. Generally, cement cleaning agent is composed of compound acid, resist and descaling accelerator, which can quickly and thoroughly dissociate the accumulation of cement scale, rust scars and other minerals, so that the sediment and the sediment in the cement scale are washed away together.

Generally, the cement cleaner needs to be diluted before use. However, cement cleaners are acidic, so be careful not to contact your skin for a long time. Cement cleaners are available in grocery stores or large shopping malls.