What to do if the toilet in the bathroom is not watered

The reasons why the toilet does not enter the water are: 1. First determine the water supply problem of tap water and hose. 2. The small filter screen inside the lower end of the inlet valve body is blocked 3. The inlet valve has been adjusted by itself, resulting in improper adjustment 4. The quality problem of the inlet valve itself.

You can open the toilet lid to check whether the float sinks to the bottom when the tank is empty, if it is still above when there is no water, it means that the float is broken, and it cannot sink and the upper water outlet is always closed, so there is no water. You can also check whether the triangle valve is open, remove the triangle, check whether the end connected with the inner wire in the wall is blocked, whether the valve core of the empty triangle valve is open and closed normally, whether the water hose is smooth, and the same exclusion can be done.

Extended Information: Cleaning Attention The toilet bowl is a passage for excretion and dirt, and it is something that we must use every day. If you don't do a good job of cleaning, it is likely to become the culprit of the threat to your health, because it is easy to breed bacteria, and cleaning the toilet bowl in daily life is actually a relatively simple thing.

1. Descaling method: pour the mixture of vinegar and water into the toilet, and after soaking for half a day, the scale will be brushed off. 2. Sandpaper descaling method:

Use the finest sandpaper to rub the toilet bowl dirt, hail imitation removes dirt that detergents can't. 3. Descaling: Sprinkle baking soda in the toilet, then brew with hot boiling water for half an hour, and the dirt can be brushed off.

4. Bleaching powder solution descaling method: wipe it with bleaching powder solution first, and then rinse it with water after a while. 5. Homemade small brushes to scrub the toilet:

The flush toilet produces yellow dirt, which is difficult to clean with a brush, so you can tie the used nylon socks to one end of the stick, dip it in foaming detergent to scrub it, and clean it once a month to keep the toilet bowl white. 6. Detergent descaling: first put an appropriate amount of water in the toilet, clean it with a toilet brush, then pour in 5-10 ml of detergent or hydrochloric acid solution, and brush it with a brush to evenly coat it.

If the dirt is heavy, you can pour a little more detergent to soak and brush until it is clean. Hydrochloric acid has a strong corrosiveness, if you use hydrochloric acid to clean, pay attention to safety, do not splash on the skin, and the acidity of hydrochloric acid is relatively strong, in the process of use does not pay attention to the material of the horse next to the bucket will cause damage, so we must pay attention to dilution when using.

1. The lever or float of the water supply component is stuck.

The lever in the toilet bowl water component is the transmission device, however, in the process of long-term use of the toilet, some scale or dirt may be attached to the activity point of the lever, making it not so sensitive, or even stuck, which also includes the float is also easy to stuck, that is, the float has been floating, in this case, the toilet inlet is sealed, and it cannot be automatically watered.

2. The outlet of the water supply component is blocked.

The water outlet of the toilet water supply component, you may not have seen it, it is a very small opening, mainly for easy blocking. Although the water flow rate will be relatively large due to the small spout, it will still be blocked by some scale or dirt if it is used for a long time. The water outlet is blocked, and even if the inlet valve is opened, the water will not come out, and the toilet will naturally not be flooded.

You can leave an inner tooth bend from the center of the drain after the tile is pasted from the toilet bowl, that is, the toilet water connection. When buying a toilet, measure your pit distance. If the position of the toilet outlet is high, you can install the water pipe first and then install the corner raft, which is seriously inappropriate, only to knock off the tiles and redo the pipe, and any other practice is improvised.

Answer pro, hello, I am happy to answer for you, please wait a moment, immediately answer for you dear, when the toilet does not have the problem of water, we have to see if the water is off in your home or someone has turned off the water inlet valve, if this is the case, then no water must not be on the water, this you have to pay attention to the owners to see when the water comes or open the water inlet valve yourself. Of course, this rarely happens, but we can't rule it out, and we still have to check it.

After the previous situation of no water is ruled out, we can give priority to the problem of the water tank, we open the lid of the water tank, check the filter screen of the water tank, the toilet tank will be practical for a long time, and the water rust filter will be blocked, resulting in the water tank not watering, we can remove the filter first, let the water first, after flushing the toilet, we are cleaning the filter screen, and install it after cleaning. In this area, I need to remind everyone to close the water inlet valve, otherwise it will cause the water to run and you may get yourself wet.

There are many reasons why the toilet can't pump water. In fact, it is very simple to investigate, and follow the flow to find it. Troubleshoot step by step.

Open the main valve [also called the angle valve] to determine if there is running water.

Open the lid of the water tank and observe that there is no water on the water tank. Whether the piston can be plugged. If you can't plug it, it will leak, and the water tank is not up to the switch, so you won't get on the water.

The toilet tank fittings are divided into three parts. The first is that the drain valve is directly below the button, and the second is the inlet valve, which is the part of the hose connected to the outside of the water tank, which is generally next to the drain valve. The third part is that the buttons are divided into full-row buttons and half-row buttons.

Close the toilet lid and see if the button can reach the inlet valve, if so, adjust the inlet valve to see if the float or float of the inlet valve can move up and down freely. If you get stuck, the water won't get in. Generally, there are adjustable crosseyes on the pontoons, and you can twist them in a clockwise direction to see.

If the float is suspended in the air when there is no water, it means that it is broken and the water inlet is blocked.

Fill the tank with water to see if the pontoons can float freely. If the problem of water inlet is solved. Then there is the problem of drainage, which is also the problem of flushing. See if the plug of the plug in the tank, also called the float, is damaged. Whether the float and button connection are loose. If it is loose, it can be tightened.

See if the button is resilient. It is easy to rust when the spring enters the water for a long time. The working principle of the toilet is nothing more than pumping--- storing water --- releasing water. Just a few things step by step. If you have more questions, you can click on ID to consult.