The living room is connected to a wired router that leads to the 3 rooms of the study, and the compu

Updated on Living room 2024-05-07
4 answers
  1. Anonymous users2024-01-23

    1. Reset the settings of the wireless router first.

    2. Set the debugging computer to automatically obtain the IP address.

    3. Connect the debugging computer to the LAN port of the router. Log in to the router and see how the router's WAN uses dynamic address acquisition.

    4. Change the IP address of the LAN port of the wireless router and save it.

    5. Turn on the wireless connection (enable wireless) and set the AP2 encryption password.

    6. Restart the wireless router.

    7. Set the wireless of the computer to be automatically obtained, connect to the wireless router, and test whether you can log in.

    8. After the test is passed, connect the network port of the master bedroom to the WAN port of the wireless router.

  2. Anonymous users2024-01-22

    1. The Internet mode of the wireless router is changed to "dynamic IP" (some routers are not called this, it is called "automatic acquisition", in fact, it means the same).

    2. Change the IP address of the wireless router to not = 1, take any number between 2-254), save, and automatically restart. You will be able to access the internet in a while. (If it doesn't work, check whether the DHCP of the wired router is turned on, and DHCP will be turned on before it assigns an IP address to the wireless router).

  3. Anonymous users2024-01-21

    The WAN port must be set for the router.

    The IP gateway is set up just like your desktop, and the last set of numbers of the IP is changed.

  4. Anonymous users2024-01-20

    The wireless router needs to be configured, and it can be that your configuration is wrong.

    Don't help post the configuration out.

Related questions
If there is a wired router in the living room, can I install another wired router in the room?
4 answers2024-05-07

A: Yes.

Connect your computer directly with your second router first, enter with the IP address behind the router, there is an account password behind it, if you don't know, you can reset the router, change your router IP to the last digit of the first router after entering the router should be 1), the previous xxx is the same as the setting of your first router, turn off the DHCP in this router, and then connect a network cable from the LAN port of the first router to the LAN port of the second router. >>>More

A wired router cannot access the Internet when you change from the living room to the room
1 answers2024-05-07

Is there no network in the route or only the computer has no network, you just put 1 meter and 10 meters to change a position, this should not be able to go online, first see if the network cable is plugged in, sometimes there is a possibility, that is, the crystal head of the network cable is not done a little problem, plug in this is normal, plug in a different place may not be in good contact,

There is a wireless router in the living room, but to my room the signal is not very good, I want to
2 answers2024-05-07

The network cable is plugged into the WAN port of your room router. Then go into the router and change the WAN address of your room route to or. The submask does not change. >>>More

The wired router in my house is in the living room and the computer is in the bedroom. I bought a wi
5 answers2024-05-07

In fact, it's very simple, first connect the wireless router with a network cable, set up the wireless router, and then replace the wired router! (Wired and wireless can be used, wired for desktops, wireless for laptops and mobile phones). Steps: >>>More

There is a wired router in the living room, connected to the LAN port to a wireless router, also con
11 answers2024-05-07

If you want to use wireless Internet access, you have the wrong connection, you should have a wired LAN connected to the wireless WAN, the wireless WAN is set to dynamic, and the LAN setting is not the same IP as the wired.