What are the tips for waterproofing and plugging leaks in the bathroom

There are several tips for waterproofing and plugging leaks in the bathroom:

The first tip: be sure to do wall waterproofing, before the wall tiles are paved, do a good job of wall waterproofing. In general, the wall should be 30 cm high in waterproof treatment, and the non-load-bearing light wall should be at least 60 cm high, and it is best to make the whole wall waterproof.

The second skill: the joints between the wall and the ground and the joints of the pipeline between the water and the water are the most likely to cause problems.

The third skill: re-paving floor tiles to do ground waterproofing If you need to replace the original floor tiles in the bathroom, after chiseling off the original floor tiles, you must first level the ground with cement mortar, and then do waterproof plugging treatment, so as to avoid leakage caused by uneven thickness of waterproof coating. Be sure to clean the ground before doing waterproofing.

The fourth technique: try not to destroy the original waterproof layer, and the ground of the newly delivered building is generally made of waterproof layer, so there is generally no leakage without destroying the original waterproof layer.

The fifth skill: the decoration team is required to make cement mulch for the upper and lower water pipes of the bathroom, brush 10 to 20 cm of waterproof paint from the ground, and then redo the ester waterproof on the ground, plus the original waterproof layer, to form a composite waterproof layer to enhance the waterproofness.

The sixth skill: the groove of the water pipe in the wall should also be waterproof, and the waterproof layer around the hole must be carefully constructed when the pipe, floor drain, etc. pass through the floor slab during the construction process. Buried water pipes in the wall, so as to achieve a reasonable layout, lay water pipes are made of grooves larger than the pipe diameter, plastering in the groove is smooth, and then brush waterproof paint in the groove.

The 7th skill: use the 24-hour "water storage test" to accept the waterproof, after the waterproof project is completed, seal the door and the drain, fill the bathroom ground with water to reach a certain liquid level height, and make a mark, if the liquid level does not drop significantly within 24 hours, especially the roof of the downstairs house does not leak, the waterproof plugging is qualified.

Master Bang, the insured waterproof leak repair service is more reliable!

The first tip: be sure to do wall waterproofing, before the wall tile paving, do a good job of wall waterproofing. In general, the wall should be 30 cm high in waterproof treatment, and the non-load-bearing light wall should be at least 60 cm high, and it is best to make the whole wall waterproof.

The second tip: the joints between the wall and the ground and the joints of the pipeline between the water and the water are the most likely to cause problems.

The third tip: re-paving floor tiles to do ground waterproofing If you need to replace the original floor tiles in the bathroom, after chiseling off the original floor tiles, you must first level the ground with cement mortar, and then do waterproof plugging treatment, so as to avoid leakage caused by uneven thickness of waterproof coating. Be sure to clean the ground before doing waterproofing.

The fourth tip: try not to destroy the original waterproof layer, and the ground of the newly delivered building is generally made of waterproofing, so there will be no leakage without destroying the original waterproof layer.

The fifth skill: the decoration team is required to do a good job of cement mulch for the upper and lower water pipes of the bathroom, brush 10 to 20 cm of waterproof paint from the ground, and then redo the ester waterproof on the ground, plus the original waterproof layer, to form a composite waterproof layer to enhance the waterproofness.

The sixth trick: the groove of the water pipe in the wall should also be waterproof, and the waterproof layer around the hole must be carefully constructed when the pipe, floor drain, etc. pass through the floor slab during the construction process. Buried water pipes in the wall, so as to achieve a reasonable layout, lay water pipes are made of grooves larger than the pipe diameter, plastering in the groove is smooth, and then brush waterproof paint in the groove.

The 7th skill: use the 24-hour "water storage test" to accept the waterproof, after the waterproof project is completed, seal the door and the drain, fill the bathroom floor with water to reach a certain liquid level height, and make a mark, if the liquid level does not drop significantly within 24 hours, especially the roof of the downstairs house does not leak, the waterproof plugging is qualified.