How to change the bathroom ceiling light when it is broken

1. First of all, the power should be cut off, so that there is no power when it is replaced, so it is necessary to choose a bright light when it is replaced, or a ruler spine can also be used to play a flashlight.

2. Disassemble the integrated ceiling plate around the integrated ceiling set, expose the keel, look for the terminal, unplug the ceiling lamp and the blind connection of the terminal, and sort out the wires of the ceiling;

3. The infiltration method of removing the gusset plate: use two harder plastic cards, insert the corners of the gusset plate, move the card to the other end, pry a little bit of the gap down with a little force, and cut out the gusset by hand. (It's like unlocking a door with a plastic sheet).

The kitchen and bathroom are clustered into suspended ceilings, and the lights are broken? Method: 1. Use a suction cup or a suction cup similar to a small hook to disassemble the ceiling plate; 2. Remove the ceiling plate with a suction cup, and remember to use an object that is too sharp to avoid scratching the ceiling plate; 3. Remove the ceiling gusset; 4. Take the lamp panel of the Ming cherry tree to replace the lamp; 5. Take out the faulty and damaged lamp; 6. Replace the lamp with a new one; 7. Connect the power socket of the new lamp; 8. Restore the lamp panel;

The cover on the ceiling lamp can be removed, you can replace the light by removing the cover on the surface, you carefully see if there are fixed screws or gaps on the edge, if there are no screws, you use a screwdriver to pry the gap on the edge of the natural open.

1. Recessed ceiling lamp.

A. The embedded ceiling lamp is mainly installed inside the integrated ceiling, and it is more troublesome to replace this kind of lamp if it is broken, because its internal structure is more complex, and remember to cut off the power supply before disassembly.

B, the buckle structure of the embedded ceiling lamp is more complex, you can not use brute force when disassembling, you can carefully observe the situation around the buckle, it is stuck with a spring clip, you only need to press and hold it and then gently break it down to replace the bulb, after the replacement, remember to reinstall the cover back.

2. Round ceiling lamp.

When replacing the lamps and lanterns of the round ceiling lamp, the power supply should be turned off first, and it is best to close the main power gate at home, so that there will be no risk of electric shock when changing the lamps.

When replacing, you can use the fixing screws around the round suction cup of the screwdriver to remove them first, these small screws are used to fix the outer iron ring of the lampshade, and then the circular suction cup, that is, the lampshade, can be rotated and unscrewed to remove the damaged bulb inside, install the bulb of the same model, and finally reinstall the lampshade.

2. Precautions for replacing chandeliers in the bathroom.

1. When taking the gusset and lampshade, you must be careful and take it lightly, so as to avoid the deformation of the lampshade and the gusset, and there is no way to restore the original state.

2. When installing, you must keep in mind the direction of taking it off at the beginning, and install it in the original direction when resetting, so that it can be restored to the original state.

3. How to connect the line and ceiling lamp from the bathroom ceiling?

The control line drawn out of the ceiling lamp is connected with the two wires of the neutral line and the ceiling lamp. Note: Disconnect the power supply before wiring.

Wiring method: 1. Strip off the insulating skin of the control line and the neutral line.

2. Strip off the insulation of the two wires of the ceiling lamp.

3. HIT TWO 6MM EYES ON THE TOP.

4. INSTALL 6MM EXPANSION PIPE.

5. Install the lampholder with self-tapping screw.

6. Wiring. 7. Restore the insulation of the wire.

8. Power-on commissioning.

Replacement method for broken ceiling lights in the bathroom: 1Remember to turn off the power first, so it is safer.

2.Generally, the bathroom is a built-in ceiling lamp, and after disconnecting the ramp of the power supply, remove the gusset next to the ceiling lamp first. 3.

Then remove the gusset of the ceiling on either side around the ceiling. 4.Remove the lampshade and install the same type of lamp again.

And next to the stool 5Then install the lampshade, and then turn on the power to see if the lamp can shine normally. 6.

Finally, fasten the gusset of the ceiling. It should be noted that when installing, you must remember the direction you took off at the beginning, and you must install it in the original direction when resetting; When taking the gusset and the lampshade, you must be careful and careful, so as to avoid the deformation of the lampshade and the gusset, there is no way to reset. Also, before replacing, you must remember to turn off the power to avoid electric shock.