-
Anonymous users2024-01-23The determination of the location of the air conditioner in the living room should mainly consider the following aspects:
1.It is easy to connect with the external unit, the pipe is short, and the indoor part is easy to hide and decorate;
2.Do not face the sofa to avoid the wind blowing directly to people and causing discomfort.
Generally, it can be located at the turning foot of the end of the exterior wall indoors, and placed at an angle of 45 degrees.
-
Anonymous users2024-01-221. The wall hole is required to be high inside and outside, 3 cm lower than the indoor unit, which is conducive to drainage.
2. Install the wall backplate of the indoor unit according to the height of the wall hole, which is generally not less than 10 cm away from the ceiling, which is conducive to air circulation.
3. After the installation of the backplate is completed, open the plastic hole of the indoor unit according to the site situation to determine the direction of the indoor unit's pipeline.
4. Prepare copper pipes, drainage pipes, and wires to connect to the indoor unit.
5. After connecting, use a bandage to wrap it.
6. Do the outdoor unit bracket, and the bracket is not higher than the window sill after the installation is completed. But it can't be too low, too low for inconvenient installation.
7. Unpack the outdoor unit, tie it firmly with a rope, go out of the window from the window, put it on the bracket and put on the shock-absorbing pad after going out. People should fasten their seatbelts.
8. Wear a shock-absorbing pad with a corner screw to prevent the shock-absorbing pad from falling from a high altitude, and tighten it with a wrench after all the corner screws are in place.
9. The pipeline is pierced from the hole to the outside, and the indoor unit is hung on the wall to ensure the stability of the machine.
10. Make the pipeline horizontal and vertical outdoors to the interface side of the outdoor unit. Use a wrench to open the plastic protective cap of the outdoor unit.
11. Match the bell mouth of the thick pipeline to the interface of the external machine, and bring the copper cap in place by hand, don't tighten it.
12. Match the bell mouth of the thin tube to the interface of the external machine, bring the copper cap in place by hand (to prevent thread damage), and tighten it with a wrench.
13. Open the shut-off valve of the thin pipe with the hexagon corner, let the gas be discharged through the thick pipe cap, and the long emptying time of the tube is (6-30S).After emptying, tighten the copper cap with a wrench.
14. Restore all the copper caps, open the electrical cover and prepare for wiring.
15. The wiring is connected in strict accordance with the circuit diagram, don't misunderstand the wrong solution, and restore it after the wire.
16. Test the cooling or heating effect when the machine is turned on, and do the drainage test of the indoor unit at the same time.
17. At the same time of the test machine, do a good job of installing the hole account, and plug the hole with cement.
1. The location is reasonable, and it can concentrate the wind direction and wind power to the position you need most. 2. After installation, it can be moved within a local range. >>>More
1. The wall hole is required to be high inside and outside, 3 cm lower than the indoor unit, which is conducive to drainage. >>>More
Air conditioners should be installed in north- or east-facing rooms. Because the northeast direction has little solar radiation, if there is only one wall on the south side, a sunshade should be installed. The air conditioning tuyere in the bedroom is generally facing the aisle next to the bed, it is recommended to re-punch the hole to install, the air conditioner is not very troublesome to move, just find a professional person.
The living room and dining room together generally need a large cooling load, according to your collocation, 2HP=, 28 square to calculate, the cold index is less than 180, obviously not cold enough, not to mention the location of your air outlet, that is, the living room is not very sufficient, let alone the dining room, the general living room cold index is matched to 230, the dining room is 250, this is more conservative, because the split machine cooling capacity is sufficient.
Adjusting the air deflector of the air conditioner can make the air conditioning air avoid the human body. >>>More