The phone fell out of the toilet

4 days? It is estimated that the chips inside are moldy now, and now take them to the maintenance place to clean them, and it is estimated that some parts will be replaced. There are often such situations in our shop to repair, and the water transfer should be brought to the maintenance department immediately!

As long as you take out the battery immediately, you will be fine, take the whole machine and blow it on a hair dryer for 10 minutes, and if you are still worried, you can put it in your pocket for a week.

Hurry up and disassemble the battery and the phone first, and don't put it on the phone and turn it on before the battery of your phone is dry, otherwise the phone will definitely not be good.

Well, don't touch it, take it out and put it in a ventilated place, and in a few days, go and see if there is a miracle happening.

Hello, it is recommended that you dry the phone first, in the boot, if not, you go to the mobile phone point to repair, water is generally a problem with the motherboard, if the repair fee is more expensive than 120, you can choose to give up.

In this case, you should take off the battery immediately, disassemble the phone if you have tools, and dry it with a hair dryer. Note: Be sure to blow dry thoroughly! Otherwise, it's not good to have a short circuit!

If the phone that gets into the water shouldn't do anything, the most wrong thing you can do is to shake the water dry

Fish it out, and it can still be used after repair.

You should take out the card first and take off the battery as soon as you take it out, and it may not be repaired.

Turn it off, let it dry, and try it on.

In the process of daily use of mobile phones, it is common for mobile phones to get wet with water, such as accidentally splashing water droplets on the mobile phone when washing hands, or not paying attention to protection when using mobile phones on rainy days and letting the rain wet the mobile phone. After the mobile phone is flooded, most of the cases cause failures such as failure to turn on, abnormal display of the mobile phone and noise on the call. And some water inlet machines corrode the circuit board more seriously, resulting in the mobile phone can not be repaired for life.

Therefore, when the mobile phone enters the water, whether it falls into clean water or dirty water, the mobile phone battery should be removed, and the mobile phone should not be charged again, such as continuing to charge the mobile phone, the internal components of the mobile phone will be short-circuited and burned out. This will further expand the fault and make it more difficult to repair, so do not charge the phone again and remove the battery after encountering water intrusion into the phone.

Then check whether your phone has been dropped into clean water or dirty water. If you fall into clean water, as long as you stop the mobile phone immediately, the fault will not be expanded. After removing the battery of the mobile phone that fell into clean water, wash the mobile phone with anhydrous alcohol.

Because alcohol evaporates quickly, the moisture on the circuit board can be volatilized and taken away. Then use a heat gun and hair dryer to dry the circuit board, and then you can charge the test machine, and most mobile phones will work normally.

If the mobile phone fell into the sewage, the first thing to do is to disassemble the phone to see the degree of corrosion of the mobile phone circuit board. Because there are many acid and alkali compounds in sewage, they will cause different degrees of corrosion to mobile phones. Therefore, after the mobile phone falls into the sewage, it should be cleaned quickly, and the corrosive materials that can be seen should be cleaned first.

Use a brush to brush off the impurities attached to the pins of the components. Then, use an alcohol cotton ball to clean the circuit board. If the corrosion is serious, it must also be cleaned with an ultrasonic cleaner, because the residue at the bottom of each element is not easy to clean, and the impurities can only be vibrated out by ultrasonic molecular vibration and then cleaned.

Then use an air gun to dry the circuit board, and then repair and solder all the chips. After welding, if it still does not turn on, or other faults, you should check whether the circuit has burned out components and whether there is a short circuit in the components according to the maintenance steps, among which the power module is more broken, most of the mobile phones that do not turn on the water inlet machine replace the power module, the mobile phone troubleshooting, and resume normal operation.

Of course, if not, then go to the repair point and have a look