How to repair a smart toilet?

1.Blockage: Insufficient flushing or falling into foreign objects or aging will cause toilet blockage, if it is a soft blockage, the use of simple dredging tools can generally be solved, if it is a hard object blockage, it is generally necessary to disassemble the toilet to dredge.

2.Water leakage: The toilet tank accessories are aging or damaged and out of order, generally because of the floating or drain sealing cover, and it can be replaced.

3.Installation problem: Use glass glue or cement when installing the bottom, and do not seal the screw holes at the bottom of the toilet bowl during installation.

4.Button failure: The most common is the double button, and the button failure can be replaced directly.

5.The wind temperature is not hot (otherwise normal): Check the drying device and computer board.

Solution: Measure whether there is 89+ -4 ohm resistance at both ends of the heating wire frame, if not, the drying device is broken, if there is, confirm the correct seat, press the drying button to measure whether there is a 220V voltage at both ends of the heating wire frame socket, if there is no voltage, the computer board is broken. If the dryer is replaced, the computer board should be carefully inspected.

Note: If the short circuit between the motor slots sometimes slows down due to the increase of load, resulting in the open circuit of the heating wire frame, it will also lead to the scorching phenomenon of the computer board D882, please replace the computer board and the drying device at the same time.

6.The water is not hot (otherwise normal): check the remote control, water tank heating pipe, water temperature sensor, thermal fuse and computer board;

Solution: whether the temperature of the remote control is set at room temperature, sit and wait for 10 minutes, if there is no heat, please unplug the resistance at both ends of the heating line of the measuring water tank is about 92 ohms, and then measure whether the resistance at both ends of the heating tube is about 92 ohms, if not, the fuse wire is broken, the resistance at both ends of the measurement temperature sensor (25K 80K) is normal, if it is normal, the computer board is broken, such as changing the water tank, after changing the detection of whether it is normal, if the water has been heating, the computer board is bad to be replaced together.

7.Seat temperature is not heated (other normal): check the remote control, seat heating wire, temperature sensor, computer board and connector;

Solution: Use the remote control to set the heating state (sit and wait for 10 minutes) If there is no heating, please unplug the heating line of the seat ring and measure the resistance at both ends to about 960+ -50 ohms, if there is no heating wire open circuit, if the resistance at both ends of the measurement temperature sensor (5K 15K) is normal, is the connector in good contact? If it is normal, the computer board is broken.

If the seat is changed, check whether it is normal after the change, and if the seat has been heated, the computer board should be replaced together.

The above are all common faults and solutions of smart toilets, if there is a failure problem that you can't handle, you should ask a professional to deal with it.

Ordinary blockages can be easily solved with a few simple digging tools; If the blockage is due to something hard, you need to open the toilet and clean it.

Smart toilet leak repair method.

If the toilet is leaking and the internal parts of the tank are aging, you need to replace the parts quickly, and the connection between the toilet and the sewer pipe is leaking, you need to reinstall the toilet and re-seal. If the toilet itself is cracked and leaks, it is best to replace it with a new toilet; The toilet was not installed properly when it was installed, resulting in the misalignment of the sewage outlet on the ground with the toilet drain diameter. In this way, yellow water, water and odors will come out and need to be readjusted.

The maintenance method of the smart toilet is not hot.

If the hot air function of the smart toilet fails, check the drying unit and computer board first, and measure the resistance of 85-93 ohms at both ends of the motor rack. If there is no resistance, the dryer will fail. If so, press the drying button to measure whether there are 220 volts at both ends of the wire rack socket.

If there is no voltage, the computer board will be damaged. When replacing the dryer, carefully check the computer motherboard.

Smart toilet installation error repair method.

If you're using glass glue or cement to install the bottom of the toilet, remember not to seal the screw holes at the bottom.

How to repair the fault of the smart toilet button.

Smart toilets don't flush automatically. There may be a problem with the button on the tank. If this is appropriate, you need to change the tank button!

As you can see from the above, even a smart toilet, this kind of high-tech furniture, will have a lot of problems, so you have to do your homework before buying enough, so that you don't get overwhelmed when you really encounter problems.

With the improvement of living standards, more and more humanized intelligent home products appear in our homes, bringing us new comfort. Smart toilets bring us a more comfortable and convenient feeling, but after a long period of use, smart toilets will inevitably have some malfunction problems. Today, I will tell you about the common fault problems and maintenance methods of smart toilets.

Common cases of smart toilet repair.

1. Blockage. Generally speaking, this problem is caused by foreign bodies or product aging, assuming that it is caused by soft objects, then you only need to use some simple dredging tools to solve, if it is a hard object, you need to disassemble the toilet for dredging, at this time it is recommended that you find a professional master to deal with, in the usual use process, should be as far as possible not to throw sundries into it, good living habits can save us a lot of unnecessary trouble.

2. Water leakage. This problem may be caused by the aging or damage of the product, which not only leads to high humidity in the bathroom, but also a large amount of waste of water resources and increased expenses.

3. The water is not hot.

This problem may be due to the failure of its own heating function, or the water temperature is inconsistent with the heat of the control, at this time we first check the remote control, water tank heating pipe, water temperature sensor, thermal fuse, computer board and other components, to see what is wrong, you can try to set the temperature of the remote control to room temperature, wait for 10 minutes, see if it is hot, if not, you need to unplug the heating wire to detect whether there is 92 ohms, if not, it is the fuse wire is broken, detect whether the sensor resistance is (25K 80K) If the computer board is broken, it should be replaced first, and then tested whether it is normal, the operation here is more professional, therefore, it is recommended that you find a professional after-sales door-to-door service.

4. The button is out of order.

When in use, you will find that other functions can operate normally, but it cannot be automatically flushed, then it may be due to a problem with its button, which only needs to be replaced, but it is recommended to choose a professional master to deal with it.

5. Installation problems.

After use, some small faults are found, which are likely to be caused by the staff's non-standard operation and installation, such as glass glue or cement at the bottom, and you must remember not to completely seal the screw holes at the bottom of the toilet.

The problem of random maintenance of smart toilets has gradually emerged, and now there are not many professional toilet repair shops, but smart electric toilets are complex electronic tools, so if you need to repair, it is better to find after-sales service.