There are gaps between the floor tiles in the bathroom, seeping water into the exterior wall, how to

As the only washing area in the family, the bathroom is in contact with water for a long time, and the brick joints are leaking, first check the cause of water seepage, 32313133353236313431303231363533e59b9ee7ad9431333264663664 Secondly, repair the water seepage area according to the reason, and finally pay attention to daily maintenance.

As the only washing area in the family, the bathroom is in contact with water for a long time, and the brick joints are leaking, first investigate the cause of water seepage, then repair the water seepage area according to the reason, and finally pay attention to daily maintenance.

Underground water pipe rupture, waterproof layer quality is not up to par, humid weather, etc. are all causes of water seepage in the bathroom brick joints, so what is the cause of your bathroom, you need to carefully investigate one by one. If the water pipe is broken, the water seepage area will become larger and larger in a short period of time, and it will cause problems with the water supply in the bathroom. If it is a waterproof layer problem, the general water seepage phenomenon will appear one after another, sometimes good and sometimes bad.

It's better to judge if the weather causes it.

Now that you know the main causes of water seepage in the bathroom brick joints, it is not difficult to find out the root cause of water seepage in your home. If the water pipe is ruptured and causes water seepage, first of all, find the distribution map of the water pipe during the decoration, find the corresponding rupture location according to the construction drawing, then open the ground to replace the damaged water pipe, and finally restore the floor.

If there is a problem with the waterproof layer, the repair project is relatively complicated, and it is necessary to replace the entire bathroom floor, rebuild the quality of the waterproof layer, and then complete the laying of pipelines and the restoration of the bathroom floor. If it's just due to the weather, then closing the bathroom windows in wet weather can effectively improve water seepage.

In daily home life, the bathroom should be ventilated frequently, and the floor should be cleaned frequently to keep it dry, which can not only effectively protect the bathroom floor and the gaps between the floors, but also provide a good sanitary environment for the family. Reduce damage to the floor and wall of the bathroom, so as to prevent water seepage in the brick joints of the bathroom.

Home problems are the top priority in life, even a small home improvement disadvantage will affect daily life, after reading this article, if you encounter.

Water seeps through the brick joints of the bathroom.

The problem must know how to solve it quickly and effortlessly.

It has been ruled out that bai is not a base.

The problem of waterproofing and water leakage is easy to deal with.

Use sharp tools to clean the original caulking cement of the tiles in the bathroom, and clean it as deep as possible. Then go to the building materials store to buy two packs of special ultra-fine seam anti-mildew caulk for ceramic tiles (there are many fakes on the market, it is recommended to buy: JCDecaux, Leibangshi, Sika, Henkel, Mapei and other brands), according to the instructions After the water is mixed, press into the tile gaps at one time according to the instructions, and wipe off the excess caulking material on the tiles with a sponge that wets the water without knowing water when the caulking material is not dry.

At the same time, make a 2-high water retaining platform that is tightly bonded to the bathroom floor at the position of the bathroom door. The bathroom tries its best to keep the ground with open water, and sweep the floor drain as soon as possible to drain if there is open water.

Tile leakage water problem, light re-caulking is a symptom is not a cure for the root cause, caulk with daily wear loss of dao

Effect, depending on your analysis, the water-containing tiles used in the bathroom leak water, resulting in the dampness and fall off of the wall putty.

It is recommended to use a new type of waterproof material without smashing bricks: infiltrating porcelain treasure, no need to smash bricks and break the soil, directly paint and construct on the surface of the tile, convenient and fast, transparent and beautiful, the material is waterproof, anti-slip and wear-resistant, guaranteed for ten years, the most important thing is to save worry and money!

Check out the bai first

Between the bathroom threshold stone and the DU door cover, the general door door cover is made on the threshold stone, and the threshold stone is required to be wet, and the row of bricks away from the door should also be wet. This prevents water from going out of the doorway. Look at whether the wall tiles are on the floor tiles, generally in, in the wall tiles and floor tiles out of the glue can be managed for a period of time, and the joints should be hooked with a special grout.

Suggestion: 1 Take down the bottom row of wall tiles, make waterproof (preferably polyurethane, not easy to buy, no, use JS), and then put tiles.

2. At the threshold stone, wet paste is used, and the threshold stone is to the edge.

First of all, find out where the water comes from and what causes it, if it really doesn't work, you can buy waterproof glue and glue the seams will be better.

You see, the threshold of the sanitary room.

Between the stone and the door sleeve, the general door sleeve is made above the threshold dao stone, and the threshold stone is required to be wet paste.

Answer, and the row of bricks away from the door should also be wet. This prevents water from going out of the doorway. Look at whether the wall tiles are on the floor tiles, generally in, in the wall tiles and floor tiles out of the glue can be managed for a period of time, and the joints should be hooked with a special grout.

There is also the method you said to treat the symptoms but not the root cause, which can be managed for up to half a year, easy to dirty, and not easy to clean up. Suggestion: 1 Take down the bottom row of wall tiles, make waterproof (preferably polyurethane, not easy to buy, no, use JS), and then put tiles.

2. At the threshold stone, wet paste is used, and the threshold stone is to the edge.

If you can be sure it's porcelain.

If the brick joints are leaking, then you need to clean up all the original cement caulks in the tile joints.

version, and the right to use the hacksaw blade to clean a little deeper, and then go to the building materials store to buy two packs of ceramic tile caulk, wipe the joint at one time do not rub the area too large, such as the wipe is not timely caulk is difficult to clean.

Find a professional waterproofing person and thoroughly do a waterproof to prevent long-term water leakage in the future.

You have to redo the waterproofing, not only the ground, but also the wall, and the wall should be waterproof on both sides in order to solve the problem. If only the floor tiles are re-jointed, it is inevitable that water seepage will continue in the future.

That's the construction problem waterproofing should be under the floor tiles, and the main problem is that the waterproofing is not in place,

If you are sure that the façade is a sign of water seepage, then I can tell you very clearly.

zhi, your.

dao decoration workers for the bathroom waterproof project must not be in place, your home is now what we often say point infiltration, directly related to the bathroom waterproof, foolproof is to let the decoration workers to leak the outer wall and the inner wall part of the shovel (the inner wall tiles must also be shoveled), redo a waterproof, the exterior wall does not need to do but to re-level the putty, if you want to be simpler, there is another way, is only to make a fuss on the exterior wall, now there is a waterproof coating called HIS, It is produced in the United States, as long as the water seepage part of the exterior wall is removed, and then coated with this paint, there is no problem, you can first learn about it on the Internet, and there is one more point, so far we do not have a very effective waterproof grout, to deal with such a problem can only be to deal with the original waterproof problem first.

This kind of water leakage at home should be caused by the leveling of the base surface of the waterproof layer, the leakage leaks to the top of the waterproof layer and then lies out along the waterproof layer, this kind of leakage as long as the water pipe leakage is eliminated can let your local hairy ants go to show you, it is estimated that it will not be too troublesome.

It is still a good choice for the use of tile surface waterproofing agent, but it must be noted that the door must be closed and installed on the bridge.

Prevent water from seeping out of the door, and waterproofing requires health treatment. At least 24 hours. Do not get wet.

First of all, check that between the bathroom threshold stone and the door cover, the door cover is generally made above the threshold stone, and the threshold stone is required to be wet, and the row of bricks away from the door should also be wet. This prevents water from going out of the doorway. Look at whether the wall tiles are on the floor tiles, generally in, in the wall tiles and floor tiles out of the glue can be managed for a period of time, and the joints should be hooked with a special grout.

Suggestion: 1 Take down the bottom row of wall tiles, make waterproof (preferably polyurethane, not easy to buy, no, use JS), and then put tiles.

2. At the threshold stone, wet paste is used, and the threshold stone is to the edge.

You see, between the bathroom threshold stone and the door cover, the door cover is generally made above the threshold stone, the threshold stone is required to be wet, and the row of bricks away from the door should also be wet. This prevents water from going out of the doorway. Look at whether the wall tiles are on the floor tiles, generally in, in the wall tiles and floor tiles out of the glue can be managed for a period of time, and the joints should be hooked with a special grout.

There is also the method you said to treat the symptoms but not the root cause, which can be managed for up to half a year, easy to dirty, and not easy to clean up. Suggestion: 1 Take down the bottom row of wall tiles, make waterproof (preferably polyurethane, not easy to buy, no, use JS), and then put tiles.

2. At the threshold stone, wet paste is used, and the threshold stone is to the edge.

Be sure to clean up the gaps.