Are there any tips for waterproof and moisture proof bathroom decoration in small apartments?

The bathroom decoration is waterproof and moisture-proof, and there are two main packages:

1. Try to choose waterproof and moisture-proof boards when decorating; It is best to choose ceramic tiles and full-body bricks for the floor of the bathroom, which has a better moisture-proof effect and is easier to clean. Walls are also generally tiled, and if you need to use special materials such as waterproof wallpaper, be sure to consider the ventilation conditions of the bathroom. When placing bathroom furniture, we should pay attention to the distinction between dry and wet, try to place the furniture away from the bathroom cabinet, good ventilation conditions, if the bathroom ventilation conditions are poor, you can let the designer design a water-blocking "screen", planning out the dry and wet areas.

2. Do a good job of daily moisture-proof treatment; The hardware of the bathroom, the water vapor and water droplets on the faucet also need to be cleaned regularly, especially after showering, there are a lot of water droplets on the hardware, and they should be cleaned up with a dry cloth in time.

The floor and walls are coated with waterproof paint. Brush two cement-based polymer waterproof coatings, you can have a good waterproof and moisture-proof effect.

At the same time, when paving porcelain tiles, ceramic tile glue, mortar glue, etc. are used to enhance the adhesion and impermeability of porcelain tiles. The use of products such as colored anti-mildew grout for the gaps between the tiles can further improve the waterproof and moisture-proof effect.

In addition, you can also install 24-hour forced ventilation devices in some particularly humid places, and stack some activated carbon and other moisture-resistant and moisture-absorbing materials.

It is recommended to use the coating of Leibangshi for waterproof and moisture-proof coating, which is of good quality and outstanding performance.

Install an exhaust fan for frequent ventilation.

Directly install a set of integral bathroom, small apartment, bathroom about two square meters.

Clean and stylish, moisture-proof and fireproof, worry-free, haha.

You can refer to it

1. When laying wall and floor tiles and stones, a waterproof layer should be made under the surface layer, the ground should be leveled with cement mortar, coated with waterproof coating, and then a layer of 1:2 cement mortar should be laid as a binding layer, and the floor tiles and other decorative materials should be paved up, and the wooden board should be used to shoot it solid after watering, so as to achieve smooth and firm and tight joints. Before the stone is paved, the back coating should be done to reduce the occurrence of "water stains". The contact between the waterproof layer and the wall should be turned upwards to about 25 to 30 cm above the ground, the washbasin should be more than one meter above the ground, and the shower room should be more than one meter above the ground.

If you do paint decoration, you should first brush waterproof putty and choose waterproof paint. To deal with the surface of the ground layer of the water to slope to the floor drain, no flooding, no water accumulation, after 24 hours of water storage test no leakage.

2. It is recommended to use a microporous aluminum gusset for the ceiling to strengthen ventilation and prevent condensation. If you make a gypsum board ceiling, you should first brush waterproof putty, and then brush waterproof coating; PVC ceilings are prone to condensation and dripping, so they should be used with caution.

3. Try to avoid changing the original upper and lower open pipes in pipeline installation, and must be decorated horizontally and vertically, laid firmly, and the slope meets the requirements. The valve and faucet are installed flat, flexible and convenient to use, and the open pipe is brushed with anti-rust paint, and the hidden pipe is brushed with anti-corrosion paint. The water supply pipeline is tightly connected with accessories and appliances, and there is no leakage after the water test.

The floor drain design should still be based on the water supply and water pipes, and the surface should be slightly lower than the ground.

4. The installation position of sanitary appliances is correct, and the upper edge of the appliances should be horizontal. Bathroom appliances should choose branded and waterproof products, such as bath warmers used in a humid environment for a long time, the shell should be made of stainless steel, with good anti-corrosion performance, and with waterproof power switches, cables and plugs, not afraid of water showers and splashes when powered on or powered off, and will not cause leakage or damage. It also needs to be equipped with waterproof lampshades, waterproof sockets, etc.

In the bathroom, the use of wooden materials should be avoided, and when it is really necessary, fireproof board or full oil decoration should be used, which can be waterproof. When doing ceiling or other package decoration, the hidden wooden keel needs to be brushed with waterproof paint or preservative.

5. It is very important to maintain a good ventilation environment in the bathroom. Choosing better quality ventilation equipment can help moisture and vapor volatilize quickly and keep the room fresh and clean. Do a good job in the above aspects, you will definitely be able to realize that in the complete release.