The water plucker can t suck the toilet is blocked, doesn t it mean that the water plucker is presse

This problem must be on your own, you might as well try it by following these steps:

Put more water in the toilet, at least to ensure that the place where the puffer touches the toilet mouth is flooded so that there is no air leakage. The pressure is greater when pressing.

Do not press intermittently, it is better to press continuously.

Continue to drain the water while pressing.

As long as it's not blocked by a hard object, this kind of pressing will definitely work.

Find the cause analysis as follows:

First of all, it may be that the size of your water pluck and the drain does not match, secondly, there is too little water when you press and suck the action, then the water pluck material is too hard and easy to turn up and leak air, and finally you do not align the sewer when you use it;

Cause Analysis:

The use method is incorrect, when using, it is necessary to ensure that the rubber sealing surface is fully attached to the toilet mouth, and then do up and down movements.

The size of the tool is incorrect, and the size of the tool you choose does not match the clogged toilet.

Solution: Find the matching tool and then process; Or contact the maintenance staff directly.

First press the water puller at the sewage outlet to block the sewage outlet, then press the flush switch to flush the water, and press the water puller vigorously at the same time, use the water to seal the water puller and let the water leak into the sewage pipe and the pressure generated by the water puller work together to flush away the blockage. Generally, one cycle can unclog the sewer, if both cycles cannot be unblocked, it proves that there is a towel or aunt towel clogged or the entire septic tank is full, so you can only call a professional to deal with it.

If you don't have a good opening, press down gently (squeeze out the air in the rubber ring), and then pull it up in a straight line, and repeat this operation until it is completed; You can also pour some water in the toilet and cover the rubber band, and repeat what I said. As long as the rubber band doesn't leak, it's fine. If you really can't do it, just call the property.

Suck that toilet bowl and don't rush to pull it out; Then fill the toilet bowl with water to ensure that the water pluck is completely sealed with the toilet bowl to have strength. After filling with water, it is enough to plug and unplug it repeatedly.

The water plucker is broken, cracked, leaking.

The water pressure is not enough, the water plucker should be completely immersed in water, the greater the pressure, the better, the toilet drain is irregularly arc-shaped, and the bottom is uneven, and the water plucker cannot be completely absorbed. It's the same as a pump.

Nowadays, many toilets are relatively special-shaped, and there are the following solutions:

Change to a water plucker, which is softer and can adapt to various shapes If the toilet is not a particularly good toilet, you can try the acidic solution DIY method, use purlins, that is, the kind of strips that pack cartons, and get a few more to stuff in and tinker Find a professional to get through, they have that kind of equipment, relatively acidic solution, which can better protect the toilet pipes If you still insist on using a water plucker, you must store the water level to the highest, and then aim to ensure that the seal is done at one time.

Don't worry, the toilet is plugged, the heart is not stuffed!

Scooters can only be used on seated toilets. The reason is that the seat toilet has a short pipe, less air in the middle, and the air pressure pressed down by the water plucker has an effect, while the squat toilet has no effect on the air pressure of the water plucker because the pipe is very long (about nearly 40 cm long). So, let's find a pipe dredge to get it through with a machine.

When sucking the toilet, be sure to aim at the toilet mouth, press down gently, squeeze out the air, and then add water to the toilet, cover the rubber ring, and then lift it straight up, repeat it several times. If necessary, you can buy a rubber ring with better elasticity and more effective.

One trick: Take a small lump of laundry detergent (lump is easy to sink to the bottom, no limit to brand) and put it in! Can!

It is completely effective within five minutes, please wash your hands after five minutes, and give points on the Internet, thank you!

Suspect something is plugging? If there is nothing hard to do, this method will serve.

Engage in a few pounds of eel loaches, to live better and stronger, you know the reason. You don't need to explain how it works, right?

Put some water around it, press it down slowly, and pull it up quickly. The water should be able to pull through the water.

Well, you try to push the water puff into the mouth of the toilet bowl, and then try to press it down to suck.

I haven't used it either, you hold it down and twist it a few times to see if it just sucks it up.

Press the flush button to add enough water, and then use the water puller to align with the drain port to quickly and repeatedly press and pull out, add water after the water leaks, and then do the above actions, so repeat several times will generally pass.