How to solve a leak in the bathroom

1. The joints should be painted in place: the joints between the bathroom wall and the ground, as well as the joints between the water and sewage pipes and the ground, are prone to problems. In the construction, we must urge the workers to deal with these corners and corners, and all the waterproof coatings must be applied "in place".

2. Wall treatment is also very important: in the general bathroom waterproof treatment, the wall should also be made about 30 cm high waterproof paint to prevent water from penetrating the wall. However, if the wall of the bathroom is a non-load-bearing lightweight wall, the entire wall should be coated with waterproof paint.

If you use two shower screens, the two walls that are connected to each other should also be fully painted. If a bathtub is used, the height of the waterproof coating should be higher than the upper edge of the bathtub.

3. Level the bathroom floor first: If you want to replace the floor tiles in the bathroom, after chiseling the original floor tiles, you must first level the ground with cement mortar, and then do waterproof treatment. This avoids leakage of the waterproofing coating due to uneven thickness.

4. The waterproof experiment must be done: after the construction of the bathroom is completed, all the sewer in the bathroom is blocked, and a 25 cm high "can" is built at the door, and then 20 cm high water is poured into the bathroom. After 24 hours, check the surrounding walls and floors for leakage.

This 24H waterproof experiment is the key to ensuring the quality of toilet waterproofing projects.

5. Keep the sewer unobstructed: all the sewer pipes in the bathroom, including the floor drain and the sewer pipes of sanitary ware, should be kept unobstructed. Only in this way can we fundamentally avoid the tragedy of the "flooding of the Seventh Army."

Reason for water leakage in the toilet 1, there is water on the upper wall near the package riser, which may be the upper layer leakage; It could also be that the upper layer leaked and leaked down the pipe.

2. If there is water in the middle of the wall, it is more likely that the buried pipeline in the wall of the house is leaking.

3. There is water on the lower ground near the riser, which may be caused by the leakage of the upper layer along the pipe, or it may be the problem of the vertical combustion pipe, the joint, valve, and cleaning port of the household.

4. Other walls are flooded at the top and the bottom of the roof is flooded, which must be the reason for the upper layer.

5. Water leakage in the ceiling may be caused by the ground on the upper floor, or it may be the leakage of the pipes in the ceiling of the household (the sewer pipes of the household and the upper floor).

1. The joints should be painted in place: the joints between the bathroom wall and the ground, as well as the joints between the high-resistant sewer pipes and the ground, are prone to problems. In the construction, we must urge the workers to deal with these corners and corners, and all the waterproof coatings must be applied "in place".

2. Wall treatment is also very important: in the general bathroom waterproof treatment, the wall should also be made about 30 cm high waterproof coating to prevent water from penetrating the wall. However, if the wall of the bathroom is a non-load-bearing lightweight wall, the entire wall should be coated with waterproof paint.

If you use two shower screens, the two walls connected must also be fully painted. If a bathtub is used, the height of the waterproof coating on the wall adjacent to the bathtub is also higher than the upper edge of the bathtub.

3. Level the bathroom floor first: If you want to replace the floor tiles of the late bathroom, after chiseling off the original floor tiles, you must first level the ground with cement mortar, and then do waterproof treatment. This avoids leakage of the waterproofing coating due to uneven thickness.

4. The waterproof experiment must be done: after the construction of the bathroom is completed, all the sewer in the bathroom is blocked, and a 25 cm high "can" is built at the door, and then 20 cm high water is poured into the bathroom. After 24 hours, check the surrounding walls and floors for leakage.

This 24H waterproof experiment is the key to ensuring the quality of toilet waterproofing projects.

5. Keep the sewer unobstructed: all the sewer pipes in the bathroom, including the floor drain and the sewer pipes of sanitary ware, should be kept unobstructed. Only in this way can we fundamentally avoid the tragedy of the "flooding of the Seventh Army."

It depends on whether you deal with it for a long time or temporarily. One is to use a plugging agent to hook the joint, this method is temporary, of course, it is cheaper. Then the floor tiles were knocked out and waterproofed again.

If the height is limited (the floor of the bathroom is lower than that of the living room or bedroom), it will be more expensive to use waterproof paint. Because the floor tiles are scrapped, in addition, they have to be labored. Depending on the size of the bathroom, it generally costs a few thousand dollars.

Bathroom leakage this is a common problem in the quality of the project, it is recommended that you find a property, let them find a construction unit to repair, if you want to do it is very troublesome, make up for your bathroom hot water or concealed installation, there is ground radiant heating, is the hot and cold water leakage or the floor radiant heat pipe leakage, or the bathroom waterproof is not done well, this should be checked one by one....These have to destroy the original bathroom floor

Depending on what you said, it could be a leaking sewer pipe, and you can take a closer look at the drains in all bathroom drains (showers, basins, toilet drains), and if your basin is a wall drain, it's more likely.

Redo the waterproofing, all at once.

You didn't explain the specific situation, the most common water seepage and leakage parts of the bathroom are around the nozzle and around the foot of the wall, I don't know if you were decorating the bathroom and re-do the waterproofing, if you simply rely on the developer to do the waterproof layer we build and easy to destroy, so before the decoration we still have to redo the waterproof layer, I don't know if you did it, if you don't do it, now do a good job is the whole is doing a waterproofing, otherwise it will be very troublesome in the future.

It depends on how the water leaks, and I don't know what specific part of the water leak you are talking about.

The bathroom should be waterproof, if there is a shower room, the waterproof should be high.

Don't be anxious if the bathroom leaks, first observe the leakage, first judge the leakage place of the toilet leakage, do the leakage test and analysis, and find the problem of water leakage. Generally, there are three kinds of water leakage: 1. The leakage of the waterproof layer is manifested as serious water leakage downstairs after bathing or ground water, and the downstairs performance may be one or more places.

The judgment method is very simple, plug the floor drain, and then release water on the ground, pay attention to the observation of the water leakage downstairs after 40 minutes, if the water leakage downstairs is serious, it is determined that the waterproof layer is leaking. In this case, you can find 100 million waterproofs on the Internet, and you can repair them by using 100 million waterproofing agents, caulking paste, and plastic steel mud. That is, the surface of the bathroom is waterproofed again, without planing tiles, saving time and cost.

2. The sewer pipe is leaking, which is manifested around the sewer pipe, and there is a serious dripping phenomenon. The way to judge is to drain the floor, the hand basin, fill the water, and repeatedly flush the toilet, and see the aggravation of the water leakage downstairs, it is the leakage of the sewer pipe. In this case, find a repairer to replace the sewer pipe and try to reduce the bricks as much as possible.

Then it also needs to be waterproofed under the ground rework, and there is no need to plane all the bricks. Yijia waterproof products can be used to waterproof the surface of the bathroom. 3. That is, the water inlet pipe leaks, if the water leakage is uniform and continuous, turn off the upper water, and the water will be reduced and will not leak.

It means that the water pipe is broken. According to your description, it should be a leakage at the floor drain interface, and you can use Yijia plastic steel mud to seal the joints, if it is a waterproof layer, you can use Yijia waterproof three-piece bathroom leakage without planing brick products. Yijia waterproof professional solves the problem of water leakage.

Shenyang can provide door-to-door service.

First of all, it is necessary to determine what is causing the water leak. For example, a broken water pipe? The waterproofing layer is not ready? Water seepage on exterior walls?

First press the water pipe, if OK, block the downspout and bathroom door, and then turn off the water for 3 days, remind the downstairs to pay attention to whether the amount of water at the original leakage point increases, or observe whether the water surface height is significantly reduced, if not, it is another reason, it may be the leakage of the outer wall seeping into the downstairs. Whether it is a problem of water pipes or waterproof layer, it is necessary to plane the floor tiles and the row of tiles closest to the ground on the wall, and then dig up the screed and backfill, drain the stagnant water, and it is best to let the backfill pit and backfill dry for a period of time, and then re-lay the pipe, backfill, leveling, waterproofing, and tiling.

It depends on whether the water pipe is leaking or the ground is leaking. If the water pipe is leaking, find out the leaking part and repair it after opening it. If there is a leak in the ground, you have to do it again.