What specifications are generally used for indoor ceilings with wooden keels and gypsum board wooden

First, the spacing of the wooden keel.

1. Use the horizontal tube to find the horizontal point, and use the ink fountain to play the horizontal line along the horizontal point;

2. Light steel keel: wooden keel for side dragon, the position of the light trough is made of wooden keel or woodworking board, and the wood production place must be brushed with fireproof coating, and the keel is the least.

50 or more, spacing.

30 cm is appropriate, and the spacing of the hanging bars.

Centimeters are appropriate, and the gypsum board and the board should be artificially reserved.

5-8 mm void, gypsum board surface self-tapping screws inverted.

1-2 mm and anti-embroidery treatment, to be flat and firm, special-shaped to achieve smooth lines;

3. Wooden keel: the least keel.

3 * 4 or more, the spacing of 30 cm is appropriate, the spacing of the suspens is 60-80 cm, the suspensory is strictly forbidden to use the wooden wedge-shaped nail to the top, brush the strict fireproof coating until the color of the wooden keel is not visible, the keel is covered with a layer of full-footed willow eucalyptus core nine centimeter board and then on the gypsum board, between the gypsum board and the board to be artificially reserved.

5-8 mm void, gypsum board surface self-tapping screws inverted.

1-2 mm and anti-embroidery treatment, to be flat and firm, special-shaped to achieve smooth lines;

4. Aluminum buckle plate: strictly required to be horizontal, light steel keel bayonet teeth to be aligned, keel spacing.

Within 50, the spacing of the hanging bars.

Centimeters are appropriate, the hands should be light when the board is loaded, so as not to press the board surface out of the pit, and the contact between the edge strip and the tile is not tight to be beaten tightly with sealant;

5. Aluminum-plastic panel: the least wooden keel.

3*4 or more, spacing.

30 cm is appropriate, and the spacing of the hanging bars.

Centimeters are appropriate, brush strict fireproof coatings, and the keel is covered with a layer of full-scale willow eucalyptus core nine-centimeter board and then pasted with all-purpose glue aluminum-plastic panel, and the aluminum-plastic panel and the board should be artificially reserved.

3-4 mm gap, has been prepared to fill other colors to play the effect of the grid, to be flat and firm, special-shaped to achieve smooth lines, the corners of the folded surface to be smooth and not broken.

Second, the home decoration wood keel process.

Wooden keel ceilings are commonly used in home decoration, and the general process is like this:

1. Read the drawings and fully understand the drawing modeling.

2. Plane the wood and brush it with fireproof coating.

3. Pop up the horizontal line of the ceiling on the wall, and fix a few longitudinal keels on the top as needed.

4. To make the keel frame, it can be nailed on the ground first, and the special-shaped top should be made with blockboard.

5. Use the boom to fix the wooden keel, and pay attention to adjusting the horizontal and vertical.

6. Reserve the position of the lamp holder bottom plate or lamp trough.

7. Connect the wires by the electrician and leave the wire ends.

8. Fix the cut gypsum board with self-tapping nails.

Generally, 30 40 ( ) can be used, and a little bigger is of course better, but it is not economical enough; If it is too small, it will affect the stability of the structure.

The length of 2 cm X 3 cm X 2 m --- 4 m is used more often for suspended ceilings.

The wall skirt is 1 cm x 3 cm.

The floor keel is basically 2 meters --- 4 meters long in centimeters x 4 centimeters or 3 centimeters x 4 centimeters.

The commonly used wood with a general specification of 30*50mm is white pine, red pine, and sylvestris pine