-
Anonymous users2024-01-23Summary. Dear, glad your question! The installation method of the rubber lap cover (that is, the sealing ring) in the toilet tank is as follows: 1. Close the water valve and clean the toilet; 2. Open the bag of the sealing ring, let its round side face up, and install it on the flange so that it is just above the opening, and fix it with screws.
3. During the installation process, ensure that the toilet is in a horizontal state; 4. Check whether the sealing ring is installed firmly, and open the water valve at the same time to test whether there will be water leakage.
How to install the rubber lap cover (that is, the sealing ring) in the toilet tank
Dear, glad your question! The installation method of the rubber lap cover (that is, the sealing ring) in the toilet tank is as follows: 1. Close the water valve and clean the toilet; 2. Open the packaging of the sealing ring, let its round side face up, and install it on the flange so that it is just above the opening mouth and fix it with screws. 3. During the installation process, ensure that the toilet is in a horizontal state; 4. Check whether the sealing ring is installed firmly, and at the same time, Lu Hongpin opens the water valve to test whether there will be water leakage.
What I asked was how to remove the old pat.
Old-style toilets can remove the toilet lid by simply unscrewing the bolts by hand, while new-style toilets can only unscrew the bolts by reaching behind them. This will be able to be removed.
One is a large patter cover, which is a small patter cover in the water tank, which is blocked at both ends, how to remove it.
It's not the kind with two buttons on it.
Yes. First of all, press one of the two rock-shaped buttons on the lid (half-moon shaped) and pry the other out with a flathead screwdriver (there is a shallow groove on the adjacent side of the two buttons), and then you can pull out both buttons, and you can see that there are plastic fastening screws inside. Use a slotted screw Chi Zao jujube knife to screw out a plastic screw that is dismantled below, so that you can take off the toilet tank cover and see its internal structure.
-
Anonymous users2024-01-22The main purpose of the rubber gasket is to make the tank sealed and watertight. The correct way is: when installing sanitary ware, put a rubber gasket between the upper and lower PVC glands and the ceramic at the bottom of the toilet bowl and tighten it, which will eliminate the possibility of water leakage.
-
Anonymous users2024-01-21How to install the rubber lap cover (that is, the sealing ring) in the toilet tank
Kiss! Hello, happy to answer your <>
How to install the rubber lap cover (that is, the sealing ring) in the toilet tank is as follows: close the water valve and clean the toilet; 2. Open the bag of the sealing ring, let its round side face up, install it on the flange, and fix it with screws; 3. During the installation process, ensure that the toilet is in a horizontal state; 4. Check whether the sealing ring is installed firmly, and open the water valve at the same time to test whether there will be water leakage. 2. What preparations should be made before the installation of the toilet seal 1. Before installing the toilet seal, you need to fill the bucket with water, and then close the main water valve in the room.
Then flush the toilet bowl and use up the water from the toilet tank while making sure there is no water in the potty. If there is any remaining water, be sure to use a sponge to wash it clean so that the subsequent Anlun can be installed. 2. At the bottom of the bedpan, find the nut cover that holds the bedpan, remove it, and ask the screwdriver to unscrew the screw.
If it doesn't work, you can easily remove it by applying some lubricating oil and loosening the nut with a vise. 3. Disconnect the water supply pipe of the toilet bowl and gently shake the toilet bowl so that it can be loosened, so that the sealing ring and caulk can be loosened more easily so that it can be removed. In the whole process, it is necessary to grasp the bedpan and not the water tank, otherwise it is easy to cause cracks in the water tank and unnecessary damage.
4. Disassemble the old sealing ring from the bottom of the toilet, then put on a new sealing ring, and fix it firmly with Tongran, and then install and fix the toilet bowl in reverse order. Note that if you don't know much about it, be sure to contact a professional to deal with it. Hope mine can help you <>
Do you have any other questions?
There's no picture.,If you want to go to the picture.,I'll tell you how to install it.。
Although there is a crack on the inside of the water tank, it is also a quality problem, and you should pick one without a crack when you buy it.
Reasons why the toilet won't drain:
1.Nowadays, a filter will be placed in the toilet tank, and after the filter is used for a long time, it will deteriorate and cause more scale to cause the filter to clog, etc., so it will cause the tap water in the tank to not enter smoothly. >>>More
The principle of toilet water supply is:
1. Use the float to control the water intake, when the water is full, the float floats up and pulls the connecting rod to close the water inlet, and the water stops. >>>More
Can be replaced, my guest bathroom's is also a broken button, just a few days ago on the Internet for a change. If the toilet button is broken, it is likely that the spring inside has lost its elasticity after a long time. When you press it, you don't have the strength to flush the toilet. >>>More