How to repair the smart toilet when there is a problem

With the improvement of living standards, smart toilets have entered thousands of households. With that comes the problem of malfunction of use. How to repair the smart toilet if there is a problem? Here are a few common faults that I hope can help you.

1) Fault phenomenon: the water is not hot (other normal).

Inspection part (remote control, water tank heating pipe, water temperature sensor, thermal fuse wire, computer board).

Exclusion method: Is the temperature setting of the remote control at room temperature? Wait for 10 minutes, if there is no heat, please unplug the resistance at both ends of the heating line of the measuring water tank is about 92 ohms, and then test whether there is a resistance of about 92 ohms at both ends of the heating tube, if not, the fuse wire is broken, the resistance value at both ends of the measurement temperature sensor (25K 80K) is normal, if it is normal, the computer board is broken, such as changing the water tank, after changing whether it is normal, if the water has been heated, the computer board is broken to be replaced together.

Smart toilet repairs can also be repaired in hundreds.

2) Fault phenomenon: the seat temperature is not heated (other normal).

Inspection part (remote control, seat heating wire, temperature sensor, computer board, connector).

Exclusion method: Use the remote control to set the heating state (sit and wait for 10 minutes) If there is no heating, please unplug the heating wire of the seat ring and measure the resistance at both ends to about 960 -50 ohms, if there is no heating wire open circuit, if the resistance value at both ends of the measurement temperature sensor (5K 15K) is normal, is the connector in good contact? If it is normal, the computer board is broken.

If the seat is changed, check whether it is normal after the change, and if the seat has been heated, the computer board should be replaced together.

3) Fault phenomenon: the air temperature is not hot (other normal).

Inspection part: (drying device, computer board).

Exclusion method: measure whether there is 89 -4 ohm resistance at both ends of the heating wire frame, if not, the drying device is broken, if there is, confirm the correct seat, press the drying button to measure whether there is 220V voltage at both ends of the heating wire frame socket, if there is no voltage, the computer board is broken. If the dryer is replaced, the computer board should be carefully inspected.

Note: If the short circuit between the motor slots sometimes slows down due to the increase of load, resulting in the open circuit of the heating wire frame, it will also lead to the scorching phenomenon of the computer board D882, please replace the computer board and the drying device at the same time.

Smart toilet repair With the improvement of living standards, more and more humanized intelligent home products appear in our homes, bringing us new comfort. Smart toilets bring us a more comfortable and convenient feeling, but after a long period of use, smart toilets will inevitably have some malfunction problems. Today, I will tell you about the common fault problems and maintenance methods of smart toilets.

Common cases of smart toilet repair.

1. Blockage. Generally speaking, this problem is caused by foreign bodies or product aging, assuming that it is caused by soft objects, then you only need to use some simple dredging tools to solve, if it is a hard object, you need to disassemble the toilet for dredging, at this time it is recommended that you find a professional master to deal with, in the usual use process, should be as far as possible not to throw sundries into it, good living habits can save us a lot of unnecessary trouble.

2. Water leakage. This problem may be caused by the aging or damage of the product, which not only leads to high humidity in the bathroom, but also a large amount of waste of water resources and increased expenses.

3. The water is not hot.

This problem may be due to the failure of its own heating function, or the water temperature is inconsistent with the heat of the control, at this time we first check the remote control, water tank heating pipe, water temperature sensor, thermal fuse, computer board and other components, to see what is wrong, you can try to set the temperature of the remote control to room temperature, wait for 10 minutes, see if it is hot, if not, you need to unplug the heating wire to detect whether there is 92 ohms, if not, it is the fuse wire is broken, detect whether the sensor resistance is (25K 80K) If the computer board is broken, it should be replaced first, and then tested whether it is normal, the operation here is more professional, therefore, it is recommended that you find a professional after-sales door-to-door service.

4. The button is out of order.

When in use, you will find that other functions can operate normally, but it cannot be automatically flushed, then it may be due to a problem with its button, which only needs to be replaced, but it is recommended to choose a professional master to deal with it.

5. Installation problems.

After use, some small faults are found, which are likely to be caused by the staff's non-standard operation and installation, such as glass glue or cement at the bottom, and you must remember not to completely seal the screw holes at the bottom of the toilet.

The common faults and maintenance methods of smart toilets are as follows:

1. If there is no function: you can check the socket of part of the power supply, the plug that leaks the protection, the button of the power supply, the contact of the installation strip, as well as the primary pole of the transformer, the panel and the computer board and other components. Whether there is electricity in the socket of the power supply, if there is, check whether the reset button of the leaky plug is pressed and whether it is displayed.

Whether the power supply of the whole machine has been pressed, the contact between the upper cover and the mounting strip, whether the secondary pole of the transformer has a 7V output, etc.

2. Blockage: insufficient flushing or falling into foreign objects or aging will cause toilet blockage, if it is a soft blockage, the use of simple dredging tools can generally be solved, if it is a hard object blockage, it is generally necessary to disassemble the toilet to dredge.

3. Water leakage: The toilet tank accessories are aging or damaged and out of order, generally if there is a problem with the floating or sewer sealing cover, it can be replaced.

4. Installation problems: use glue or glass cement when installing at the bottom, and do not seal the screw holes at the bottom of the toilet during installation.

5. Button failure: the most common is the double button, if the button fails, you can replace it directly.

6. The water is not hot (other normal): check the remote control, water tank heating pipe, water temperature sensor, thermal fuse wire and computer board.

7. The seat temperature is not heated (other normal): check the remote control, seat heating wire, temperature sensor, computer board and connector. Use the remote control to set the heating state (sit and wait for 10 minutes) If there is no heating, please unplug the heating wire of the seat ring and measure the resistance at both ends to about 960+ -50 ohms.

The resistance value at both ends of the sensor (5K 15K) is normal, is the connector in good contact? If it is normal, the computer board is broken. If the seat is changed, check whether it is normal after the change, and if the seat has been heated, the computer board should be replaced together.