I always feel that the pressure of my toilet tank is too small, and it is not good to flush it, so I

It's a problem with the design of the toilet!

Please take a look at the water tank, if the water outlet is covered by rubber, just change it to a hammer nozzle!

Because of the rubber cover pad outlet, the water flow is diagonally drained outward, and the cover pad cannot instantaneously cause the due water flow due to the influence of the pulling facility, when the water is all discharged.

The impact of the front is not enough for the water flow.

It's already in the sewers!

The impact of the water flow in the back is enough, but not enough to form a toilet.

Siphon force vacuum, so sometimes it can't be flushed clean!

The toilet bowl is in need of punch and siphon.

Double force work!

If the spout is already hammered, check the toilet outlet.

The close connection with the sewer is in condition!

- Lonely mountain man.

There are many models of toilets, and there are many kinds of problems with toilet tanks, and there are three main reasons that need to be eliminated: first, the problem of the tank itself; the second is whether there is a problem with the water ingress; The third is whether there is a problem with the water, last month there was also a problem in my house, and there was a slow leakage, and then I invited a master to help me change a full set inside and outside the water tank, and now it is good!

1. The design of regular water tank products on the market should be able to meet the requirements of flushing, and now the products on the market have considered the water-saving requirements, and they are designed with two buttons, so there is no need to find a way to reduce the amount of water discharged from the water tank.

2. Please lift the lid of the water tank to see if there is any debris or blockage inside.

3. After lifting the lid of the water tank, press the water release button to see if the water flow meets the requirements, if the requirements are met, that is, the button on the lid needs to be adjusted.

4. If none of the above situations exist, you need to ask a professional to see if it needs to be replaced.

FYI.

First, it has to do with the size of the sewer pipe of the water tank

Second: the flushing water of the water tank is not enough.

Third: the siphon structure of ceramics is not very good.

1: How much water is stored in the toilet.

2: The toilet flush encounters some internal pipe friction in the process of downflow, which reduces the power of the flowing water.

3: It is recommended to replace the water tank with a large water storage.

The first depends on how long your toilet has been, and after a long time, there will be something blocked in the toilet outlet, and second, the toilet is also divided into high and low grades, which are too bad and do not have good odor-proof quality.

Third, whether the toilet lid is sealed on the toilet, so that the water will not come out quickly

The biggest reason why the toilet can't be flushed cleanly is.

The water pressure in the house is not enough.

The solution to the water pressure problem is as follows:

Check the toilet bowl to see how much water pressure is needed.

Call the property management company to confirm what the water pressure is at home, and if you fail to meet the water pressure required by the toilet, see if you can adjust the water pressure to solve this problem!

Put two large bottles of Coke in the tank. The large Coke bottle should be filled with water to give the tank more pressure. Try it, it feels okay.

Open the lid of the water tank, and there is a rod to adjust the amount of water inside. Make it shorter and the amount of water will be higher each time. If you really can't adjust, find a professional water tank seller to take a look.

Is there something blocked in your toilet? You try a few more times to rinse and put some dish soap.

Most of the water pressure is not enough.

Because the pressure of the water tank is beaten.

The easiest way is to change to a toilet with a higher tank.

Add water to increase the pressure, and add water from P=F S to increase F, then P will increase, so that it can be washed out.

There wasn't much water in the tank.

You can look for the property. Or install a water pump.

You know why.