How do you replace the toilet seat?

Netizens provide solution 1: When changing the toilet lid, we need to remove the fixing bolts on the back of the toilet to replace it; When installing, you can operate in the opposite direction. There is no difference in size of the general toilet seat, just adjust the two bolts when installing.

But you also need to measure the size, the distance between the screw holes, the width and length of the toilet seat, and then buy a new toilet seat to replace!

Netizens provide solution two: Go around the toilet bowl to see where the screw cap of the toilet lid is, then choose a suitable wrench, just take off the screw cap, the position of the screw cap of the toilet cover is divided into two types: bright and dark, the bright place is easy to find, but the screw cap in the dark is not easy to see, the general position is set at the edge of the toilet tank, so open the lid, put your hand in, and feel the direction of the water tank to see if there is a screw cap. To install the toilet seat, you need to remove the fixing bolts at the back of the toilet, remove the previous toilet cover, and then replace the new toilet seat with a fixed screw cap.

At present, most toilet seats are large and small, as long as the screws at both ends of the toilet are done. However, the size of the toilet bowl must be measured before changing the toilet lid, and the width and length of the screw cap from the toilet lid also need to be determined. So as not to buy products that do not fit.

Netizens provide solution three: Different styles of toilet seats are installed differently, in general, the bottom end of the toilet lid is connected to the position of the toilet, and the back is screwed up, as long as you reach down and find it, you can take off the entire cover by unscrewing the screws on both sides, it's very simple, you can try.

Netizens provide solution four: You can find a professional to replace it for you. So how much does it cost to change a toilet seat?

If you are looking for a professional team, then the price cannot be determined, because there will be differences in the fees of each place and each person, and it is impossible to give an exact figure.

Non-original, source network. Hope it helps. Thank you.

Ordinary for intelligent, the size should be good, the specifications should be optimistic, the brand should be selected, and the merchant package should be installed. Replace the ordinary ones by yourself, tear off the old ones, install the new ones, the plastic screws can't be screwed down and can be cut with a knife, and the small saw blade can be cut, anyway, it's useless, and it doesn't matter if you disassemble it violently.

The toilet has become an indispensable sanitary ware in every family, but after a long time of use, it is inevitable that there will be some problems, such as buying a bucket lid that is broken, in this case the toilet lid needs to be replaced, so how to replace the toilet cover? What do I need to pay attention to when replacing a toilet seat? Let's take a look with me!

1. How to replace the toilet seat.

First of all, open the toilet cover, find the screw cap that fixes the toilet, use a wrench to remove the screw cap, and replace it with a new screw cap, but the location of the screw cap is more difficult to find, some are in the light, but some are in the dark, the dark screw cap is generally close to the water tank, if you really don't know how to replace the toilet cover, you can find a professional to replace it.

Second, what to pay attention to when replacing the toilet seat.

1. When replacing the toilet seat, you should first buy a toilet seat of the right size, so as not to find that the size of the toilet seat is wrong during installation, which will cause unnecessary trouble. Before installing the toilet seat, it is best to clean the toilet bowl to ensure that the toilet bowl is clean and tighten the screws of the toilet seat to avoid the situation that the toilet seat will shake during later use.

2. Observe the root of the toilet cover, you can see two round screws, these two screws are used to fix the toilet cover, but some screws are sealed by the cover, in this case, you need to pick up the cover plate to remove the two screws, remove the screws and then install the first new toilet cover, and tighten the screws.

3. In addition, in the process of installing the toilet lid, it is necessary to resist the measurement of the rejection of the hidden bird, and at the same time ensure the accuracy of the measurement results, and the error must be controlled within one centimeter, otherwise it will affect the normal use of the toilet. After installing the toilet seat, check that the toilet seat is opened and closed smoothly.

Summary: The relevant content of how to replace the toilet seat is introduced to you here, I hope to help friends in need. In fact, the replacement of the toilet seat is not complicated, but when replacing the toilet seat, the parts must be put away so as not to find the parts when installing the toilet seat.

There are two rotten hats under the hinges behind the toilet seat, and you can remove the old toilet lid and replace it with a new one by turning it to the left.

When replacing the toilet seat, simply remove the fixing bolt on the rear of the toilet bowl to replace it; When installing, you can operate in the opposite direction.

Toilet seats are large and small, just adjust the two bolts when installing.

Dear, hello, I'm glad to answer for youAnswer: The way to change the toilet seat is as follows: Find a nut, remove it with a wrench, and replace it with a new toilet seat. The position of the screws may be in the light or in the dark, and it is impossible to find the location of the toilet seat screw cover.

It may be on the side of the tank inside the toilet bowl and open the lid. If you put your hand in it and touch it upwards and in the direction of the tank, you should be able to feel it, but you can't see it. When replacing the toilet seat, simply remove the fixing bolt on the back of the toilet bowl to replace it.

Most toilet seats are size-agnostic, adjusting the two screw weights when installing will do, however, you also need to measure the size of the toilet seat, the spacing, width and length of the screw holes, and buy a new toilet seat for replacement. This method can help us to replace the toilet seat better. Pay attention to the newly purchased toilet seat accessories, and then fix the bolts and buckles to the Yinjingling bracket, and the left and right buckles can slide to facilitate the plugging holes.

In addition, you can also change it in this way. Place the bolt into the hole in the screw and fix it with a screwdriver to make sure the bracket does not slide. The new toilet lid is aligned with the bracket mouth, and the toilet lid is stuck into the bracket, and it can be fixed tightly, so that it can be replaced, isn't it very simple?