Leaking water at the connection between the toilet bowl and the floor

The leakage of water at the connection between the toilet bowl and the floor may be due to the following reasons:1Toilet quality reasons:

The quality of the toilet itself is not up to par, and the sealing of each connection is not good, resulting in water leakage. 2.Toilet installation problems:

The toilet is not installed properly, and the gap is too large, resulting in a water leak. 3.The ground is waterproof, and the friends are done:

If the waterproofing of the ground is not done well, after the toilet is installed, the ground will settle, resulting in gaps and water leakage. 4.Clogged pipes:

Clogged pipes can also cause toilet water to not drain properly and leak. It is recommended that you contact a professional maintenance personnel for inspection and repair.

Kiss! Hello Tongran, I am happy to answer your <>

The reasons for the leakage of the pro-toilet and the ground connection are as follows: First, there is a problem with the toilet itself, many friends are greedy for cheap when buying the toilet, and the toilet is used more frequently, and after a long time, the inferior toilet is prone to quality problems, such as cracks, etc., resulting in leakage at the connection between the flush and the ground. In this case, you can only ask a professional to deal with the problem of toilet leakage.

If it still can't be repaired, you have to replace it with a new toilet. Second, the installation is not clear, resulting in leakage, if the toilet is just installed and there is a leak in the connection, it is likely to be caused by not being installed. Check for yourself whether the toilet connector is connected, and then see if the seal is installed.

If there is still a water leak, immediately contact the merchant to send the installer to reinstall. 3. The sealing valve cover is not tight enough for the toilet bowl to be used for a long time, and the sealing valve may not be able to cover the displacement phenomenon, resulting in the leakage of the toilet base. In this case, you can directly purchase a sealed valve with guaranteed quality and replace it directly.

Fourth, the water inlet valve does not have a filter to lead to water leakage, if the water inlet valve is not equipped with a filter, and there will be impurities in the water, after a long time, the accumulated impurities will block the sealing ring in the air inlet valve, resulting in automatic closure during use, and the connection between the toilet and the ground will leak. This can solve the problem of water leakage by simply cleaning the sealing ring, if it still doesn't work, just replace one. Hope mine can help you <>

Do you have any other questions?

The leakage of water at the connection between the toilet bowl and the floor may be due to the following reasons:1Toilet quality reasons:

The quality of the toilet itself shall be investigated and replaced. 2.The gap at the bottom is too large:

If the gap at the bottom of the toilet bowl is too large, this kind of problem often occurs, and the solution is to readjust the glass glue at the bottom of the toilet bowl so that it is smooth and free of gaps. 3.There is a gap between the cover and the ground:

This may be due to the large space between the toilet seat and the floor, and the solution is to use a seal to seal the two between. 4.Drain pipe failure:

When the toilet is flushed, there will be a siphoning phenomenon, sucking away the water from the car, if the drain pipe fails, the toilet water can not be sucked away, there will be a leakage, the solution is to find a professional to replace the drain. To sum up, solving the problem of leakage at the connection between the toilet bowl and the floor requires corresponding repairs or replacements depending on the specific cause.

Summary. If the connection between the toilet bowl and the floor is leaking, there may be several reasons:1

Improper installation: Incorrect installation of the gasket at the junction between the toilet bowl and the floor, or the fastening screws are not tightened, can cause water leakage. 2.

Aging gaskets: Aging or damaged gaskets at the connection between the toilet bowl and the floor can also cause water leaks. 3.

Problems with the toilet bowl itself: If there is a problem with the drain hole or drain pipe of the toilet, it can also cause a leak. Here are some things you can do about these issues:

1.Check the installation: Check that the gasket at the connection between the toilet bowl and the floor is installed correctly and that the fastening screws are tightened.

2.Replace the gasket: If the gasket is aged or damaged, a new gasket will need to be replaced.

3.Check the toilet problem: If the above two measures do not solve the problem, you need to check whether there is a problem with the toilet itself, such as whether the drain hole or drain pipe is blocked, etc.

If you are not familiar with these operations, it is recommended that you have them inspected and repaired by a professional plumber or maintenance personnel.

If the connection between the toilet bowl and the floor is leaking, there may be several reasons:1Improper installation:

Incorrect installation of the gasket at the junction between the toilet bowl and the floor, or failure to tighten the fastening screws, can lead to water leakage. 2.Gasket aging:

Aging or damaged gaskets at the connection between the toilet bowl and the floor can also cause water leaks. 3.Problems with the toilet itself:

If there is a problem with the drain hole or drain pipe of the toilet, it can also cause a leak. In response to these problems, you can take the following measures:1

Check the installation: Check that the gasket at the connection between the toilet bowl and the floor is installed correctly and that the fastening screws are tightened. 2.

Replace the gasket: If the gasket is aged or damaged, a new gasket will need to be replaced. 3.

Check the toilet problem: If the above two measures do not solve the problem, you need to check whether there is a problem with the toilet itself, such as whether the drain hole or drain pipe is blocked. If you are not familiar with these operations, it is recommended that you have them checked and repaired by a professional plumber or maintenance personnel.

Dear, do you have any other problems that you don't understand and need to solve for you?

1. Confirm that the water parts inside the water tank are installed correctly and tightly. It can be closed with glass glue at the bottom of the water inlet and the junction of the water tank. The bottom of the flush part is also treated.

2. Confirm that the rubber ring at the connection between the water tank and the toilet body is elastic enough, and the connection between the water tank and the toilet body is tight enough.

3. Apply neutral glass glue to the rubber ring between the water tank and the toilet.

4. Before the construction of the glass glue, please wipe the sizing part dry (absolutely dry). It is best to keep it without water for 24 hours after construction.

5. If the flange is not installed, you need to disassemble the toilet and then repair it, or buy a new flange to reinstall it, and then fix the toilet with glass glue.

6. If there is a crack in the toilet toilet, it is better to replace it with a new toilet.

7. The sealing ring problem needs to replace the sealing ring of the toilet base. After the toilet is put on, glass glue is played around, or you can mix the cement with water on the toilet base first, and then put the toilet seat up and put it steady, and then use the mixed white cement to seal the toilet footsteps in a circle, and you can use it when it is dry. Be careful not to let the white cement fall into the pipe when installing, otherwise it will cause the pipe to be blocked.

8. For the repair of the leakage of the toilet base, you can find a special maintenance personnel to thoroughly inspect and repair the toilet.

9. The loose toilet base needs to be repaired, and the problem can be solved by the following methods:

1) Change the sealing ring.

2) If the base is loose, pad things in an empty place, such as pad wires, until it does not shake, and then make a circle of glass glue.

3) Get the toilet up, dry the toilet bowl and the floor, measure the distance between the front and back, put the toilet in the middle, draw a line with a pencil, 4) take the toilet away, on the pencil line, on the glass glue, on the toilet seat, wipe the outside glue with your hands, do not flush for a day, do not sit on the toilet until the glue dries.

This means that your toilet drain does not have a full match with the ground sewer, and you will need to reinstall the toilet bowl - if it does, there will be no water in the gap with the floor.

The bottom of the toilet is leaking, which may be the source of the toilet water.

The connection between the mouth and the ground sewer outlet is not installed with a sealing flange

Bit. At this time, you need to disassemble the toilet, buy a new DAO flange and install it from scratch, and then fix the toilet with glass glue. The glass glue only plays the role of fixing the toilet bowl on the ground without moving the position, and does not play the role of draining water when the toilet drains.

If the main sewer pipe is drained smoothly, the flange will not leak to the outside if it is slightly misaligned.

Toilet bottom.

Water storage inside the toilet; Use a wallpaper knife to remove the sealant between the bottom of the toilet bowl and the floor tiles. Move the toilet to clean up the stagnant water, check the gasket for deviation or damage, and correct or replace it. Seal the gap between the toilet base and the floor with glass glue and let it stand for 24 hours before use.

Pump up the toilet, clean the floor, and re-glue the glass, or cement.

Hello very copy

I'm glad to answer for you, here's how: Close the water valve of the toilet tank; Then drain the water inside the tank; Move the position where the toilet is in contact with the floor vigorously to stagger the original position; Wipe the ground near the toilet drain pipe, especially the silicone on the toilet floor; (The connection between the toilet installation and the ground is mostly fixed with glass glue or directly cement.) Then clean the glass glue on the outline of the bottom of the toilet, and then wipe the contour position of the ground and the outline of the bottom of the toilet with a dry towel without water traces; Put it in its original position and re-fix it with glass glue to seal it.

1. All the bottom of the toilet is leaking, which may be due to the fact that the connecting sealing flange between the toilet outlet and the ground drain is not in place. At this time, you need to disassemble the toilet, buy a new flange and install it from the new, and then fix the toilet with glass glue.

The glass glue only plays the role of fixing the toilet bowl on the ground without moving the position, and does not play the role of draining water when the toilet drains. If the main sewer pipe is drained smoothly, the flange will not leak to the outside if it is slightly misaligned.

Leakage at the connection between the toilet bowl and the floor may be due to the fact that the outlet at the bottom of the toilet is not aligned with the outlet on the ground, or the water level of the toilet tank is not high enough, or there is a quality problem with the toilet itself. There are some possible solutions to eliminate subordinates:1

Align the toilet outlet and floor outlet: If there is a leak at the junction between the toilet bowl and the floor, it may be due to a misalignment of the toilet outlet and the floor outlet of the Narak. You can use a level or tape measure to check that these two outlets are aligned, and if not, you will need to reinstall the toilet or the floor to ensure alignment.

2.Check the toilet tank level: If the toilet tank level is not high enough, it may cause the toilet to not seal adequately and leak.

You can check if the water level of the toilet tank is high enough, and if it is not high enough, you can increase the water level or adjust the position of the tank. 3.Check the toilet quality:

If there is a quality problem with the toilet bowl itself, such as a damaged toilet bottom seal or a cracked toilet bottom, etc., it can also cause water leakage. If this is the case, you can contact the toilet manufacturer or a professional repairer to resolve the issue. 4.

Replace the seal: If the seal at the bottom of the toilet bowl is damaged or aged, it can cause water leakage. You can buy a new seal and replace it, or contact a professional repairer to resolve the issue.

In conclusion, if there is a leak at the connection between the toilet bowl and the floor, you need to check the alignment, tank water level, toilet quality, and seal, etc., and take corresponding measures to solve the problem according to the specific situation. If you can't solve the problem by yourself, you can contact a professional maintenance person to deal with it.