How to change the rubber sheet of the kitchen halter

It is not necessarily that the rubber mat is leaking, but it is more likely that the internal parts are not in place if the handle is loose.

The inner core of this type of valve is usually a complete assembly, which is replaced by a set.

The products of each manufacturer vary greatly, and some special tools may be required when disassembling. The specific words are not clear, and the following can only be used as a reference:

Remove the handle: There will be a small fixing screw on the handle, and the handle can be removed by loosening it. The small screws are hidden relatively hidden, and you think that most of them are to unscrew the small rod (which may be subject to reverse threading) and fix the hole below the small rod (mostly hexagon screws);

When the handle is removed, the inner core assembly can be seen. (Sometimes there is a cover that can be snapped off), move which square column on the inner core to see if the faucet can be turned off, you can know whether the valve core is faulty or the handle is not good.

Unscrew the upper cover (also called the spool pressure mother) to remove the inner core. The method of unscrewing the upper cover is different, the following picture is to use a special hexagonal socket to screw the hexagon, there are also two eyes to insert the tool to rotate, when there is no professional tool, you can also use a large pipe wrench to directly screw the outer spherical shell (troublesome and easy to break).

There are many styles of spool pressure mothers, and some are divided into several parts that need to be disassembled separately.

After the inner core is removed, replace it with an inner core of the same specification (available in hardware, plumbing, and home improvement stores).It's better to take the old ones with you

Note : What you wantMixed spool There are many spools of solar water valves and floor heating water distribution valves that look very similar to it, and even the shell is the same part.

Now these water taps are all ceramic cores and have no rubber pads. Generally, when the cage handle is removed, the ceramic core can be seen.

If it is a hot and cold water nib. Use a small screwdriver to pry open the red and blue plastic cover (that is, the thing that represents the sign of hot and cold water), you can see a screw with a slotted slot inside, very small, you have to look at the light obliquely to see it, use a screwdriver to loosen it (rotate to the left is to loosen it), at this time, as long as the handle on the top is lifted up, after the handle is taken out, you can see a large nut, this nut may be tight, you need to use a large wrench or pipe wrench to loosen it (to the left rotation is to loosen), This allows you to see the ceramic spool.

Usually the whole orientation comes, change the whole faucet, if the store you buy gives you the old ceramic chip, usually the minimum is ten yuan. Our family's whole thing has been changed, and it is easy to change seventy or eighty to one or two hundred. If you want to be more durable, change to three or five hundred, thousands.

Generally, the ceramic inner core is stuck back in place, just clean it, the second is that the red rubber pad is aging, just replace it with a new one, if not, find a black rubber pad in the picture, and then put the red one back.

On the reverse side of this faucet, there are two roses fixed faucets, and the faucet can be taken down by removing the ross and the connected hose. But this is very troublesome, it is better to remove the basin together to facilitate the repair of the faucet.

Do you seem to have a leak in the spout and base?

The water outlet is not a problem with the rubber pad, there are two porcelain tiles inside, just over a year, just tighten the screws!

The screws are inside the movable handle cap.

If the base is leaking, it shouldn't be a problem with the rubber pad, but also if the screws are loose, take them all off and go to the plumbing store, and they will tell you how to tighten the screws.

Just like my faucet, go to the building materials market in your city, there are faucets sold everywhere, just buy a gasket and replace it. Remove it as it is, and put it on as it is.

Remove the faucet and put on the rubber pad.

Turn off the water, and get the faucet down.

I twist the top one down and change it to a pad.

You can go to the hardware store and ask.

I don't know why it works.

Symmetrical knots are painstakingly where you are.

Uncle is too much, a subway sentence, daughter-in-law is hi, delicious and has a good effect v annoying v korean drama eating ha v newcomer.