What is the reason why the toilet does not store water

The toilet tank does not store water, which is caused by the rubber sealing gasket of the toilet drainage system, due to the aging of the toilet drainage system for a long time or the impurities at the sealing gasket, which is caused by the poor sealing of the gasket.

Due to the importance and frequency of use of the toilet, slow drainage is a very troublesome topic. In addition to the reasons for later use such as clogged pipes and insufficient water pressure. Choosing the wrong toilet is also an important factor.

If you choose the wrong toilet, even the best toilet will drain slowly. In addition to looking at the displacement, pit spacing, and quality of the toilet, it is especially reminded that you also need to look at whether the sewer pipe has a trap.

If there is a trap in the sewer pipe, then only a floor-standing flush toilet can be used. If you don't have a trap, you can use a siphon toilet and a wall-hung toilet. What is the reason for this?

It turns out that the siphon toilet comes with a trap and the trap of the sewer pipe are superimposed, which will trap air in the middle and cause poor toilet drainage.

So how do you tell if your own pipe has a trap?

1. The easiest way: Before installing the aluminum gusset in the bathroom, look up at the pipe setting on the top of the bathroom, which is the easiest and safest method, regardless of whether there is a displacement of the customer.

The following is the difference between a village bend and a bend without a trap.

2. The more complex operation method is suitable for friends who have installed aluminum gusset in the bathroom and do not want to dismantle, or who are installing gypsum board.

Prepare tools: a large basin of water, a long stick.

First pour a large basin of water into the sewage pipe, then poke into the pipe with a long stick, and then take out the pipe to observe whether there is a large area of moisture at the end, if there is a large area of moisture, it means that the pipeline has a trap, if there is no moisture, it means that the pipeline has no trap. (This method is limited to cases where the pipe is not shifted).

Choosing the right toilet is usually the first element of drainage, of course, in addition to the toilet purchase, you must also pay attention to the flange interface when installing the toilet. The flange connection is misaligned, which will also cause the toilet to drain slowly. Therefore, when the master installs the toilet, it is best to supervise the whole process, and be sure to confirm that there are no mistakes in the installation location and method.

1. There are many reasons for the toilet to run out of water, such as the toilet inlet pontoon is separated by the water tank wall or other parts, the filter core is blocked by debris, the inlet pontoon is low, etc., which need to be treated according to the specific reasons.

>2. The leakage water inlet pontoon is separated by the water tank wall or other parts, and the treatment method: appropriately adjust the position of the return field of the water inlet buoy.

3. The filter of the toilet is blocked, and the solution: remove the filter and clean it, and then install it.

4. The water inlet pontoon is low, and the treatment method: adjust the pontoon appropriately high.

5. There are debris stuck between the inlet float and the small water tank, and it cannot move up and down.

6. The debris will be stuck in the low water inlet parts, and the treatment method is to remove the check valve to clean up the debris, and then install the crack.

This answer applies to most brands of toilet models.

The water tank does not store water The first problem is the soft connection of tap water You can unscrew it to see if there is water If there is water It is the floating ball in the toilet tank is broken or stuck You can slightly twist the buckle on both sides of the soft connection below Be sure to twist it along the way Twist it backwards is to remove it Twist it a little Sometimes the floating ball is stuck on the side and does not bounce up If the floating ball does not bounce up, it will keep going into the water How much to go down Of course, there is no water storage There is another reason is that the switch in the toilet tank that pops up when you press it The rubber mat inside should be uneven, can not be sealed, the buckle is not tight, it is too long, or the water quality is not good, if that, you have to change a set of toilet tank water parts, the price is about 20 yuan, plus the labor cost of 30-50 yuan, a total of 60-80 yuan, will solve the problem is perfect.

1. The water purification pontoon is isolated by the water tank wall or other components, and the location of the water inlet pontoon tank needs to be adjusted appropriately.

2. The toilet filter is clogged, you need to remove it and clean it up, and then restore it to its original state.

3. If the inlet pontoon is too low, it needs to be adjusted to an appropriate height.

4. There are debris between the inlet float and the water tank, which makes it impossible to run up and down, so the debris needs to be disposed of and adjusted to a suitable level. location.

5. The sundries resist the water purification parts, and the return valve needs to be removed and cleaned up, and then installed back.

1. The toilet does not store water because the water storage tank is faulty. The main reason may be the aging of the rubber gasket of the water discharge system or the impurities at the sealing gasket and the poor sealing of the gasket. 2. The toilet water storage tank is mainly composed of two parts: the water inlet and the water discharger.

When the drain fails, the water cannot be stored, the water inlet is always inlet, and the drainer is discharging water at the same time. 3. Repair method: a If you don't understand, ask the hydraulic master to repair; If you know a little bit about repair, you can repair it yourself - tighten the water drainer so that the mat under it is tight, and it will naturally not leak, and if it doesn't work, you need to check whether the mat is damaged, if so.

There can be many reasons why a toilet bowl is not holding water, and here are some possible reasons:

1.Flushing system failure: The flushing system of the toilet bowl is composed of a water tank, an inlet valve, a water level valve, a foot valve, etc. If any of these areas fail, the limb toilet will not hold water. For example, the inlet valve is not closed tightly, or the water level valve fails.

2.Clogged sewers: If the sewer is clogged, the drainage will be slower, the amount of water discharged will naturally decrease, and the toilet will no longer hold water.

3.Leaky toilet: If the toilet itself has a leaking problem, the water will keep flowing out, eventually leading to a water outage.

4.Broken pipes: If a pipe breaks, it can cause problems in the entire water system. This situation is serious and needs to be dealt with immediately.

5.Insufficient water pressure: If the water supply pressure is insufficient, it will cause the toilet to run out of water.

6.Water supply stops: Sometimes, water utilities stop water supply, such as city pipe repairs, which will result in toilets without water supply.

The above are some of the possible reasons why the toilet does not store water, and I have always tried to find the source of the specific problem by carefully checking the status of the toilet bowl and flushing system, and then solve the problem in a targeted manner. If the problem is more serious, you need to find a maintenance person who specializes in the divine industry to avoid more serious consequences.

The toilet does not store water, and generally speaking, it is said that there is no water in the water tank, which may be due to the leakage of the sealing ring of the water tank, and the water tank does not store water.

Then it is necessary to check the sealing ring of the water tank, replace or repair and maintain the eardrum from below I can't store water, he is a tubular structure, there should be no water leakage, if the test tube of this bend is rotten, it is possible, no water storage, in general, there is no this, S bend rotten situation?

What is the reason why the toilet is not small, one is that the pressure valve of the flush cannot be returned or the rubber pad is not sealed and leaking, and the other is that the water will not enter the water if it hangs up.

The toilet does not store water because the water storage tank is faulty, and a professional master is found to repair it.

No problem, the siphon toilet is flushed before the toilet is returned I feel that your pipe is a little problematic, you can really judge the reason by flushing it directly with the basin water.

What are the reasons why the toilet does not store water: 1. There are many reasons why the toilet bowl is not watered, such as the toilet inlet float is separated by the water tank wall or other parts, the filter core is blocked by debris, the water inlet float is low, etc., which need to be treated according to the specific reasons. 2. The inlet pontoon is separated by the water tank wall or other parts, and the treatment method:

Adjust the position of the inlet pontoon appropriately. 3. The filter of the toilet is blocked, and the solution: remove the filter and clean it, and then install it.

4. The water inlet pontoon is low, and the treatment method: adjust the pontoon appropriately high. 5. There are debris stuck between the inlet float and the small water tank, and it cannot move up and down

Clean up the clutter and adjust the appropriate position. 6. The debris will be stuck in the low water inlet parts, and the treatment method is to remove the check valve to clean up the debris and install it again.

This answer applies to most brands of toilet models.

1. What is the reason why the toilet does not store water? 1. The inlet pontoon is separated by the wall of the water tank or other parts, and the inlet pontoon bucket needs to be appropriate. 2. The toilet filter is blocked, it needs to be removed and cleaned up, and then it can be restored to its original state.

3. If the buried water buoy is too low, it needs to be brought to an appropriate height.

Nowadays, many people are equipped with toilets in their homes, but there will be various problems after using them for a long time, so what is the reason why the toilet does not store water?

1. What is the reason why the toilet does not store water?

1. The water purification pontoon is isolated by the water tank wall or other components, and the location of the water inlet pontoon tank needs to be adjusted appropriately.

2. The toilet filter is clogged, you need to remove it and clean it up, and then restore it to its original state.

3. If the inlet pontoon is too low, it needs to be adjusted to an appropriate height.

4. There are debris between the inlet float and the water tank, which makes it impossible to run up and down, and the debris needs to be disposed of and adjusted to a suitable position.

5. If the sundries resist the water purification parts, you need to remove and clean the return valve, and then install it back.

Second, what is the problem with the two holes in the back of the toilet that have odors?

If there is a problem with the toilet, it will emit a large odor, and we must take corresponding measures to deal with it, and the following is the solution to the odor in the two holes behind the toilet.

1. The purpose of the small hole in the rear is to fix the bottom corner of the toilet, but now there is no such method, most of them are treated with silicone sealant, and if they are not closed, they will smell bad.

2. If the sealing ring loses its effect or is not installed in place, it is necessary to close the hole in the back again, or reinstall the toilet and reinstall the sealing ring.

If the base is not clean or uneven, you can remove the glue of the sealing ring, put it directly on the sealing ring and install the toilet, and then use the sealant to make a circle along the base, which can avoid the problem of bad smell.

I conclude: the above is the reason and solution for the lack of water in the toilet, from the above article we can see that if we usually find that there is a problem with the toilet, we must clean it in time, otherwise there will be a peculiar smell after a long time, and cause secondary damage, early detection of the problem and early treatment, can avoid unnecessary consumption, save a lot of manpower and material resources, I hope to help everyone.