-
Anonymous users2024-01-23Your own waterproofing layer is not done well and needs to be redone, but you have to redo the waterproof layer to resurface the floor tiles. If only the upper and lower water pipe casings leak, they can be plugged with the plugging spirit, which will be slightly ugly, but the amount of work is small.
-
Anonymous users2024-01-22In the construction project, this situation is generally all dismantled and waterproofed, the waterproof material is made of two-component polyurethane waterproof coating, generally 3-4 times, the thickness reaches more than 2mm, the actual four times are generally close to 3mm, the ground is full of brush, the wall height is meters, and the wall is semi-dry and is stained with granular sand again, so as to facilitate the bottom tiling;
There are two points to pay special attention to in the actual construction: the riser is handed over to the cast-in-place plate and the bottom stone of the door, and the treatment method is: the root of the pipe is chiseled 30-40mm deep, and the high-elastic vinyl waterproof tape is wound 3-4 times (high-pressure waterproof tape can be replaced), and the pipe root can be re-smeared with Jintang without leakage, and the waterproof is the same as the ground; The bottom stone of the door must be brushed about 50mm high on the façade to prevent leakage;
After drying, press the water for 48 hours, check for leakage, and if there is a problem, waterproof maintenance, no leakage will be qualified;
-
Anonymous users2024-01-21Why don't you test the water first after the waterproof is done, it is the most troublesome to repair after the decoration is done. There are two ways to do this. First, you first find an awl as thin as a tile joint, "sharp things, mud knife tips can sometimes be", fill the cement in the joints deeply, and then buy a bag of water without leakage, "water does not leak, you can't buy poor, good is not expensive", water does not leak, take a little water, mix well with water, not too thin, not too dry, and then fill in the seams scraped out of the tiles.
The second is that if the downstairs of the bathroom is hung on the roof, the board of the ceiling will be removed and the waterproof professional will be used to block it with a grouting machine. If neither works, then the only option is to re-do the waterproofing.
-
Anonymous users2024-01-20There is no choice but to do it all over again.
-
Anonymous users2024-01-19Is it the ground or the shower area Is it that the waterproof base layer has not been treated well before.
The reason for the water leakage is that the waterproof layer before the tiling of your bathroom is not in place, or it is not waterproof at all. There is no good solution to the problem, only to remove the bricks, redo the waterproof layer, and then apply the bricks. If you negotiate with them without results, then take the construction contract signed by both of you and sue the other party to the court, and the court will give you a correct answer.
It's annoying, how can you not do a good job of waterproofing when you used to decorate? The matter has come to this, and there is no need to be sad, considering the cost problem, you don't have to move here, help the next door shovel the wall skin, batch waterproof putty, and then brush latex paint!
The early stage did not do a good job of waterproofing, need to see what the leakage is, generally speaking, there is no floor drain in the kitchen, there is only one sewer pipe, if the top surface is the sewer pipe from downstairs, there is a watermark around the sewer pipe, then it may be that the sewer pipe is cracked, so you can only find the property to replace the other is that the waterproof layer of the ground is destroyed, the water will penetrate the tiles and then leak downstairs, so it is very troublesome, you need to take all the tiles off and then all the waterproof, and then pave the tiles.
1.Resurfacing floor tiles should be done to waterproof the floor. >>>More
Contact the property in your neighborhood first to determine who is responsible. >>>More