What s going on with the toilet all the time

This is the float in the tank at the back of the toilet that controls the water inlet valve There is a problem, so the water inlet valve keeps open, so the water keeps on.

1. You only need to close the water inlet valve, open the upper cover of the water tank, remove the blue plastic soft cover on the water feeder (the round pipe and other devices), and then remove the small bolt at the other end of the float, remove the small round black rubber gasket, turn it over and install it again, and finally install the parts as they are, which will generally solve the problem.

Second, the toilet water inlet device can not be closed normally, it may also be that the float valve of the water tank is damaged, because it can not automatically float and close, the water does not stop working, and it is always in a state of non-stop water, you can open the toilet cover, observe the flexible state of the float and other accessories, whether there is any accessory friction obstruction interference, rule out these possibilities or not, it is recommended to replace the new float valve device.

3. If the above does not work, you can only ask someone to fix it.

Tank float valve malfunction. There is a float valve in the water tank, when the water supply reaches the set value, the float valve will automatically float to stop the water inflow. If the float valve is damaged or deteriorated, it will naturally cause the toilet tank to stop watering.

2.The flush switch is faulty. If the water tank is flooded and drained at the same time, it is likely that the flush switch is damaged or jammed due to excessive wear.

Asked whether it was changed to a new one or kept on the water.

Answer: First, you only need to close the water inlet valve, open the upper cover of the water tank, remove the blue plastic soft cover on the water dispenser (the round pipe and other devices), and then remove the small latch at the other end of the float, remove the small black round rubber gasket, turn it over and install it again, and finally install the parts as they are, which will generally solve the problem. Second, the toilet inlet device can not be closed normally, it may also be that the float valve of the water tank is damaged, because it does not have the automatic floating closing effect, the water inlet does not stop working, and it is always in a state of non-stop water, you can open the toilet lid, observe the flexible state of the float and other accessories, whether there is a friction obstruction and interference of accessories, and it is recommended to replace the new float valve device.

Hope it helps, dear

The float inside is out of order, so fix it.

It is because of the blockage of the toilet, which is usually divided into two types: one is the blockage of soft substances (usually feces, paper towels, rags, etc.), and the other is the blockage of hard objects (toothbrushes, plastic bottle caps, small combs, small toys, pens, etc.). Of course, there may be other reasons for the blockage, such as problems with the pipes themselves.

First of all, we can check whether the flush switch is restored to its original state, because the flush switch in some toilets is easy to wear out after being used for a long time, or it is stuck, so it cannot be restored. Typically, the switch can be reset by repeating it a few times.

We can check the limit device of the water level of the lower tank, whether it is loose, or whether it is too high, if it is too high, the water in the tank will exceed the overflow level and flow from the overflow pipe into the toilet.

We can also check whether the outlet of the lower tank is blocked. If the plug at its outlet is worn or something is blocked because of it, the plug is not tightly sealed, and the toilet will also run out.

If the toilet is always on the water, maybe it is a problem with the water tank, you can check whether the material or parts of the water tank will be too old, because some small parts are relatively unused, and it will not take long for the phenomenon of damage, if it is used for a long time, there will be problems, then it is a phenomenon of natural wear and tear, as long as it is replaced, the phenomenon of leakage on the toilet does not stop and cannot be eliminated, it may be because of the sewer pipe, because the function of the sewer pipe is used to connect the toilet tank, It is also possible for a major conveyor pipe to have this problem.

1.When you find that the water on the toilet bowl does not stop, you should first check the cause and then take measures to deal with it.

2.If it is caused by the water tank, check whether the accessories in the water tank are aging or damaged, and then replace them with new ones.

3.Because there is a problem with the sewer pipe, it should be replaced with a new one.

It may be that the device that controls the water inlet is broken, and you have to open the lid to take a look, if you haven't done it, you have to find a hydraulicist to repair it, which is very convenient, and now you have to close the water inlet valve below.

Go to the place where you bought the valve and change it, it is likely to be a quality problem.

If the toilet is flooded all the time, then it is likely that there are several problems:

1.Water tank problem: The float in the toilet tank is not rising, which means that the water in the tank has been flowing, causing the toilet to be filled with water non-stop. In this case, you can open the tank to see if something is stuck with the float or if you need to replace one of the accessories in the tank.

2.Water leakage: If there is no problem with the water tank, then there may be a leak in the connecting pipe between the toilet and the water tank. In this case, it is necessary to determine where the leak occurred so that the leak can be repaired.

3.Blockage: If there is no leakage in the connecting pipe, then it is necessary to check whether the toilet drain is blocked. A clogged toilet drain can also cause the toilet to be flooded all the time.

4.Valve problem: There is also a situation where the water on the toilet bowl keeps flowing because other valves such as shower valves, side leak correctors, etc. are broken. In this case, the corresponding parts also need to be repaired or replaced.

To sum up, if the toilet bowl is flooded all the time, it is necessary to conduct a specific analysis according to the actual situation to find out the problem and then prescribe the right medicine. In daily use, the toilet bowl should be cleaned, maintained and maintained regularly, which can effectively avoid various problems in the toilet.