The balcony made a fish pond, pasted tiles, what should I do if I test the water and find a leak?

Personally, I think there are two treatments, one is the most thorough and the other is simpler.

Back to the treatment method, the most thorough treatment of the aquarium leakage. In fact, if this approach is mentioned, probably everyone disagrees with me.

Because this method requires all the tiles to be broken and then waterproofed. After the waterproofing is completed, a closed water test is carried out, and only after passing the test can the tiles be pasted. Simple treatment of water leakage after tiling of aquaculture ponds, this treatment method takes advantage of the waterproof properties of the tiles themselves.

At this time, we found that the tiles were leaking after sticking to the aquarium. We only need to deal with the joints of the tiles. Personally, I would recommend that you use an outdoor general purpose weather-resistant silicone structural sealant to deal with cracks in your tiles.

First clean the tile gaps, and then fill the tile gaps with structural adhesive After such treatment, there is basically no water leakage, here is a specific standard practice involving fish ponds.

Let's give you a detailed introduction, when we finish the structure of the fish pond, we need to do the first waterproofing at this time. The waterproofing material can be a polymer waterproofing coating or a polyurethane waterproofing coating. Specific painting method:

Brush each corner first, first three times; Then brush the large surface at least three times. After brushing, perform a closed water test. After the sealing water is qualified, the wall is plastered with wool and then tiled.

Here we need to pay attention to a few key issues: the first is to strengthen the treatment of all corners, and the second is to pay attention to at least three times. The third thing to note is to do a closed water experiment after the painting is completed.

The material of the fish pond is very particular, the material can be replaced, and the concrete can be used to rebuild one.

You can find the leak first and then replace a tile.

You should first find the leak and then plug it with a special tool.

Find the leak and see if the leak is particularly serious, if it is serious, it is recommended to do it again to waterproof.

Find out the source of the leak, and then fix it with the right medicine, and you should be fine.

If there is a water leak, you need to find the leak and fill it with cement.

Turn off the water switch first to see if there is a leak between the tiles, if so, just change it.

This solves the problem, it really can't be done, use styrofoam to stick a layer on the outside.

Check first to see what went wrong, and then fix the problematic area.

In recent years, it is still more popular to build a fish pond on the balcony, although it is a very self-cultivation thing, but the construction can be a loss of trouble, if the construction is not done properly caused by water leakage, it will be bad to quarrel with the downstairs neighbors.

A simple way to deal with the leakage of the fish pond after the tiles are pasted. This treatment method is to use a waterproof performance of the tile itself. At this time, we found that there was a leak after the fish pond was tiled, and we only needed to treat the brick joints of the tiles.

Personally, I recommend that you use the kind of weather-resistant silicone structural sealant that is used outdoors to treat the gaps in the tiles. First of all, clean the tile gaps, and then use structural adhesive to fill the tile gaps tightly. After this treatment, there is basically no water leakage.

However, glue injection can only solve the problem in the short term, and it will not work in the long run.

Personally, I think that the real "once and for all" way is to break the tiles and re-construct them. The closed water test must be done, and it is stricter than in the bathroom, after all, the fish pond can always be impounded, so it is not a simple brush twice waterproof can be done, and the closed water test must also go through 48 hours. Once a water leak is found, it should be remedied in time, and do not wait until the tile is finished to be found.

After the closed water is qualified, the wall is brushed, plastered, and finally tiled.

If you want to build a fish pond on the balcony must find a reliable master, the waterproof quality must be passed, once there is a leakage in the later stage, the tile should also be finalized and re-waterproofed. It should be noted that it is not possible to do waterproofing directly on the tile, which will affect the decorative effect, and secondly, the tile is too smooth, and the waterproof material bonding effect is not very good.

If there is a water leakage problem, check what is the cause of the water leakage?

The specific practice of the balcony fish pond There are generally two ways to make a fish pond on the balcony. These two practices are also the most popular at this stage, and I will tell you about them one by one.

The first way to make a fish pond on a balcony was to use bricks. That is, directly take bricks to build a wall, and then build a square or rectangular pool; The surface layer is waterproofed, plastered, tiled, and later served as a fish pond and placed on the balcony.

> the second specific way to make a fish pond on the balcony is concrete. This practice is to support the formwork on the balcony first, and then start pouring concrete, and finally remove the formwork to appear the appearance of the fish pond we need. The surface layer is also waterproof, plastered, and tiled.

Personally, there is a question to be said here. Since balconies are cantilevered structures, they are limited in terms of force. Therefore, I personally suggest that it is best not to make a fish pond on the balcony, whether it is a brick structure or a concrete structure.

Because the fish pond itself is coupled with the water in the fish pond, the weight is very high, and it will cause the balcony board to crack over time.

> after the tiles were applied to the surface of the fish pond, the water was tested and it was found that there was a water leak. At this time, I personally think that there are two ways to deal with it, one is the most thorough way to deal with it, and the other is a relatively simple way to deal with it.

The most thorough treatment for leakage in fish ponds. In fact, you may not agree with my point of view when you say this method. Because this method needs to smash all the tiles that need to be pasted, and then redo the waterproofing, do the closed water test after the waterproofing, and start to paste the tiles after passing the test.

A simple way to deal with the leakage of the fish pond after the tiles are pasted. This treatment method is to use a waterproof performance of the tile itself. At this time, we found that there was a leak after the fish pond was tiled, and we only needed to treat the brick joints of the tiles.

Personally, I recommend that you use the kind of weather-resistant silicone structural sealant that is used outdoors to treat the gaps in the tiles. First of all, clean the tile gaps, and then use structural adhesive to fill the tile gaps tightly. After this treatment, there is basically no water leakage.

> if there are pipes nearby and the pipes are underground, it is advisable to break down the balcony tiles to find the location of the water seepage. Balcony tile joint seepage can not be without a source, the best solution is to go to the source, to solve it completely at one time, can not wait, the problem is big, water leakage downstairs will be troublesome.

Since your home is a fish pond leakage, I suggest that it is best to knock off the tiles and redo the waterproofing, because all the current materials and processes can not solve the problem of not knocking the tiles and stopping the leakage for a long time. In addition, the fish pond must be stored for a long time, and the requirements for waterproofing must be higher. For a long-term and effective solution, it is better to knock off the tiles and do it again.

Otherwise, the money spent on repeated repairs is enough to re-do the waterproofing, and it is better to solve the problem once and for all.

> after the tiles were applied to the surface of the fish pond, the water was tested and it was found that there was a water leak. At this time, I personally think that there are two ways to deal with it, one is the most thorough way to deal with it, and the other is a relatively simple way to deal with it. The most thorough treatment for leakage in fish ponds.

In fact, you may not agree with my point of view when you say this method. Because this method needs to smash all the tiles that need to be pasted, and then redo the waterproofing, do the closed water test after the waterproofing, and start to paste the tiles after passing the test. A simple way to deal with the leakage of the fish pond after the tiles are pasted.

This treatment method is to use a waterproof performance of the tile itself. At this time, we found that there was a leak after the fish pond was tiled, and we only needed to treat the brick joints of the tiles. Personally, I recommend that you use the kind of weather-resistant silicone structural sealant that is used outdoors to treat the gaps in the tiles.

First of all, clean the tile gaps, and then use structural adhesive to fill the tile gaps tightly. After this treatment, there is basically no water leakage.

The first way is to smash all the tiles and re-lay them; The second is to reinforce and waterproof the brick joints of the tiles at the leakage to plug the leaking gaps, but this method is not used for a long time.