How to install a toilet

1. Before installation, check whether there is any blockage such as mud and sundries in the sewage pipeline, and whether the installation ground is level.

2. Determine the center of the sewage pipe and the center of the toilet outlet, and adjust the wall within the error range.

3. Determine the installation position at the bottom of the toilet. Dry installation: Use an electric drill to drill the installation holes and embed the expansion screws. Wet and dry installation: Use an electric drill to drill the installation holes and embed the expansion screws.

4. Install a sealing ring on the sewage outlet of the toilet, or put a circle of glass glue around the sewage pipe, put the toilet according to the position of the line, and adjust the level.

5. Dry installation: screw on the screws and seal a circle of white cement around it. Wet installation: Adjust the landscaping sealing surface.

6., installation and commissioning of tank accessories. Depending on the situation, some need to do this first.

In addition, some toilets are difficult to debug if they are found to be abnormal after installation due to their emphasis on aesthetics (although this situation is not much, but it has also been encountered), it is recommended to test the water before installation.

7. Install the toilet cover. Depending on the situation, some need to be done first.

8. After installation, it should wait for the white cement or glass glue to solidify before use, generally 24 hours.

How to install a toilet at home.

1. Check the leveling between the sewage pipe and the ground.

Before installing the toilet, the sewage pipe should be comprehensively inspected to see if there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation is level.

2. Determine the center of the sewage pipe.

Flip the toilet bowl over to determine the center on the toilet drain and draw a cross center line that extends to the bottom of the toilet bowl around the feet.

3. Fix the toilet.

Align the reticle line between the toilet bowl and the ground drain outlet, keep the toilet installed horizontally, and press the sealing ring tightly, and install the anchor screws and decorative caps.

4. Do a good job of bottom sealing.

5. Install the water tank accessories.

Drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes; Then install the angle valve and the connecting hose, then connect the hose with the installed tank fitting inlet valve and press the water source.

6. Debugging and inspection.

Check whether the water inlet and sealing of the inlet valve are normal, check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and whether there is leakage to install the filter device of the inlet valve. Shanghua decoration will answer for you.

1 Treat the ground drain as high as the ground, and then press the center of the outlet to draw a cross extension. 2 Draw a crosshair along the toilet outlet to the spot where you can see the edge of the toilet, 3 Put the horse to the drain with the crosshairs overlapping. 4 Draw a line along the outside of the toilet bowl and remove it.

5 Place the toilet sealing flange on the drain on the ground, and make a circle of glass glue along the inside of the overall circle line of the toilet bowl. 6. Place the toilet on top of the crosshair, press the bottom edge of the toilet on the glass glue, connect the water hose, and install an angle valve at the water outlet on the wall to turn off the water for maintenance in the future. 7 Do not use and keep the ground dry for 24 hours.

2. Determine the center of the sewage pipe and draw the center line of the cross.

3. Determine the center on the toilet drain and draw a cross center line.

4. Determine the installation position at the bottom of the toilet, use an electric drill to lay the installation hole, and embed the expansion screw.

5. Install a special sealing ring (i.e., wax flange or rubber flange) on the sewage outlet of the toilet or put a circle of glass glue (putty) or cement slurry around the sewage pipe, and the ratio of cement to sand is 1:3

6. Align the cross line on the toilet with the cross line on the ground, install the upper toilet, and then put a circle of glass glue (putty) or cement mortar at the bottom of the toilet. The ratio of cement to sand is 1:3, and the toilet installation should be kept level.

7. Screw the screws on the toilet mounting holes.

8. Install and debug the water tank accessories. After installation, connect the water source, check whether the water inlet and sealing of the water inlet valve are normal, check whether the drainage valve and the installation position correspond to each other, whether the installation is tight, whether there is leakage, check whether the length of the button switch chain is appropriate, whether the switch is flexible, whether there is a chance to jam, and check whether there is a leakage to install the water inlet valve filtration device.

9. If you find any abnormalities in the trial process of adjusting the toilet, please refer to the "Common Faults and Treatment Methods of Toilet Tank Accessories, Check and Deal with It".

10. After the toilet is installed, it should wait until the glass glue (putty) or cement slurry is solidified before it can be used with water. The curing time is generally 24 hours.

The installation methods of various toilets are different, and the most common toilets are equipped with a sealing flange on the toilet drain, and a circle of glass glue is played around the base, and then the toilet is placed on this circle of glass glue.

Some toilets themselves have a plastic sewage pipe, according to the manufacturer's requirements, you have to fix the sewage pipe with expansion screws first, and then install the toilet.

There are also toilets with two holes and three holes, and you need to change the hole spacing in advance before installing.

Home renovation is indispensable to install toilets, which are the work of decorators. There are all kinds of toilets, if you are a decoration worker who has not mastered the technology, you can learn from the master, and you can master the installation technology through internship.

1. Before installation, check whether the sewage pipeline is smooth and the installation ground is clean.

2. Install the matching sealing ring on the sewage outlet of the toilet.

3. Determine the installation position of the toilet. Align the toilet drain with the pipe drain to adjust the correct position, and then use chalk or whiteboard markers to mark the line around the toilet and determine the installation holes.

4. Punch installation holes. Align the anchor screwing marking hole, use a percussion drill to punch the mounting hole, the diameter is 10mm, the depth is 60mm, and the expansion glue nail is loaded, and the anchor screw is generally not installed.

5. Label the inside of the marking line with glass glue.

6. Align the installation hole and the surrounding glass glue to install the toilet, and slowly press down until it is horizontal.

7. Put glass glue on the connection between the toilet and the ground, and trim the surrounding area to ensure the appearance.

8. Install the anchor wire.

9. Connect the water inlet pipe and check whether the filter is installed next to it.

10. Clean the ground and tools, and prohibit immediate use. Because it usually takes 24 quarters of an hour for the glass glue to cure, it is necessary to keep the area around the toilet free of water for 24 quarters of an hour.

Follow the instructions to install.

1. Squatting in the pit to change the toilet, first measure the distance from the center of the drain to the wall. Buy a toilet according to this distance. Don't buy the so-called squatting toilet for sitting, pick a siphon toilet with a suitable hole spacing.

2. Before installing the toilet, be sure to test whether the sewer pipe is unblocked. Method: Fill a bucket of water, quickly pour the whole bucket into the sewer, and pay attention to see if the water level in the sewer has risen. If there is a rise, it must be completely dredged first, and if it does not rise, it is qualified.

4. If possible, it is best to go downstairs and replace the sewer pipe with a direct elbow. Squatting pits use a trap. It is not good for toilet drainage. Then you don't have to do a second job.

1. Before choosing a toilet on the market, first determine the size of the water in the seat (i.e., the distance from wall to wall). Before installation, please make sure that the product accessories you choose, completed, please carefully review this manual and learn about some products.

2. Determine the height of the drain according to the condition of the toilet and cut off the rest of the part. The goal is to make the plumbing and toilet bottom more consistent. Start by using a hacksaw or cornea for the sewer according to the horizontal height of the centimeter, because the flange of the toilet bowl is soft.

If it is not centimeters high, there may be water seepage problems, and centimeters are more tightly fitted.

3. Measure the pit distance. Before choosing a toilet, first determine the size of the water inside the house, that is, the distance from the wall to the water. When using a toilet, if you want to decorate the tiles, you must measure the pit distance after applying the tiles. Otherwise, the toilet will be bought back and cannot be installed.

4. Install the flange ring provided with the toilet at the drain. Remember to press hard to ensure the compaction of the flange ring and toilet drain. Place the flange on the toilet drain.

Then carefully align the lower hose and lower it smoothly. At this point, the wall of the sewer pipe is inserted into the viscous clay of the flange for sealing.

5. After the water test is completed, start to install the cover.

6. Glue around the toilet, this step is also very important, not only to stabilize the toilet, but also to prevent the smell of the net from being released from the toilet. Therefore, we will not only fight, but also four whole weeks. At the intersection of the toilet bowl and the outer surface of the floor, since the toilet bowl and the floor are not one, a joint seal transparent sealant can be used for agitation, and the outer opening of the toilet bowl is sealed to maintain the integrity of the floor.

Some bathroom water can clog around the toilet bowl. NOTE: IF YOU NEED TO INSTALL THE SET SCREWS, FIRST APPLY A SPECIAL SEALANT INSTALLED IN THE TOILET BOWL EVENLY ON THE OUTSIDE 2CM OF THE TOILET BASE.

The drain of the toilet bowl should be pulled towards the center of the drain. Expansion bolts are located on the left and right sides of the toilet, remove the toilet, punch holes and raised bolts.

7. Install or debug the water tank accessories.

8. After installing the toilet, wait until the glass glue (putty) or cement mortar has solidified before releasing water. The curing time is usually 24 hours.

This kind of toilet mat is equally suitable for the O-shaped U-shaped toilet, this kind of toilet mat is more troublesome, first put the toilet mat under the toilet lid, the seat plate is upright, and then the inner ring of the elastic band is turned out from the hole in the seat plate on the reverse side, remember that the circle without a hard ring passes through the toilet seat as a whole, wraps a part of the cover surface, and finally turns down the outer ring with a plastic tube to cover the bottom of the seat.

How to install a regular toilet:

1. Before installation, take out the pipe plug of the ground drain outlet, carefully check whether there is any debris in the pipe, and then clean the area around the nozzle.

2. Make sure that the floor where the toilet is installed is hard and flat, and cannot be paved with floor tiles or other decorative materials, and if there is sand and gravel debris, it should also be cleaned up.

3. Before fixing the toilet, it is recommended to calibrate it with a level.

4. Fix the toilet.

5. Remove the sealant adhered during construction, and be sure to remove it in time before it dries, so as not to be difficult to remove after drying.

6. Connect the water inlet pipe and make sure that there is no leakage.

7. After about one hour of installation, the water is continuously tested several times to ensure that the sewage pipe is unblocked. To test the effect of toilet drainage, the method is to install the accessories in the water tank, fill it with water, put a piece of toilet paper in the toilet and drop a drop of ink, if it can be discharged at one time without leaving a trace, it means that the water is unobstructed.

8. It should be noted that the toilet should not be used within three days after the installation is completed, so as not to affect its stability.