How to calculate the material of the ceiling

The household conventional plate with integrated ceiling is 30X30, that is, a plate is a square, and a square is... Block plates.

Both the keel and the corners are 3 meters long as standard. If you're a dealer or installer, this question doesn't make sense, unless you're just starting out. If you are the owner, it depends on the size of the room you need to decorate, length or width, you have to cut the root or according to the basic length of the keel, the main shirt is a steel keel can owe a little on both sides, because it is responsible for the area load-bearing, but the triangular keel must be on the side, because it needs to be used for card plates.

You have to do the math, but keep in mind that the length of a main light steel keel or a triangular keel is three meters. As long as you have basic mathematical knowledge, you can figure out how to cut the material is suitable.

As for the corners, the perimeter of the room you want to decorate is the length of the corners you need, and you can consider more than one or two, because it will produce the necessary excess according to the specific length of the room.

Finally, let's talk about the suspension bars, which should be calculated according to the length of the ceiling sagging from the roof or this regret. A light steel keel needs at least 3 suspenders, and one with more suspenders needs to be longer, and then one plus comes out.

There are four parts to the integrated ceiling area calculation: gusset, ceiling appliances, edge banding and installation.

The first part is the gusset part. If the ceiling of the room needs 12 square meters, first divide 12 square meters by the area of a single piece to calculate the number of pieces, fold out the area, and then calculate the final square number. Sometimes the ceiling area of the room is not neat, and it is necessary to cut a single piece, and the cut part still needs to be counted as an area, because the merchant has paid the cost, but the proportion is very small.

The second part is the edge strip, which is measured in meters, and the grade is also divided into medium, low and high-grade.

Rice. Loss: 3% 2) Accessories:

Hanger - for hanging the main keel Pendant - for hanging the auxiliary keel with the main keel Connector - for the hooking of the auxiliary keel joint Connector - for the connection of the main keel joint The main keel hanger: 1 piece per meter The main keel hanger: 1 piece per meter The main keel hanger: per meter X0D X0A auxiliary keel pendant:

The number of pendants = the total number of auxiliary keels Connectors: Connectors = the total number of auxiliary keels The length of the side of the ceiling frame 3) Hanging material : a. Standard lifting analysis x0d x0ab, self-made hangers:

Boom material, anchor iron, nail or expansion bolt, boom nut. X0D X0AA) on the boom of the human keel skeleton with about 8 steel bars, and at one end of the boom to make a section of 30mm long thread. b) Do not use 10 galvanized iron wire as a boom on the keel.

L-shaped wall side keel, T-shaped main bone and T-shaped cross brace keel combined forming a, side keel according to the length of the ceiling perimeter calculation. vents, light troughs. X0d X0AB, the ceiling with the main keel and the cross brace keel, first count how many main keels, and then multiply by each length, the number of cross brace keels is the same as the main keel.

Hanging parts, iron wire, cement nails, self-tapping screws, aluminum blind rivets x0d x0aa, hanging parts are mainly used expansion screws or nails to fix the iron hanging points, only hanging points per square meter. b. 12 iron wire for hanging: 10kg 100.

c. Cement nails, used to fix keels along the edge of the wall, 2 m. d. Self-tapping screws and aluminum blind rivets are used to connect the keel frame, and the specifications of aluminum blind rivets are 4 10 or 5 10:16 Self-tapping screws are M4 15 or M5 15:

16 pcs