How to adjust the toilet water level

Step 1 First of all, we lift the lid of the toilet, pay attention to be sure to hold it firmly, handle it gently, and do not bump it.

2 We see that there are two black columns on the toilet lid, this is the toilet water discharge connecting rod, this can be adjusted to control the strength of the toilet button, this should not be adjusted too long, so that the lid can just touch the blue block and yellow block below. It can be adjusted to one long and one short, for example, you can press the small button on the lid when you are done urinating, and the drainage is relatively small.

4. If the water level is higher than the overflow pipe, then we adjust the position of the float on the left, rotate the white rod in the circle, which can be used to adjust the high and low position of the float, after rotating a few times, release part of the water, and then observe the water level after the water storage stops until it reaches the satisfactory position.

5 At the same time, we also see that in front of this water button, there is a yellow block that can be moved up and down, this is used to adjust the toilet drainage, if you feel that the toilet button is pressed once, the drainage is too large or too small, you can adjust the height of this small yellow block, so as to achieve a satisfactory drainage.

END Considerations.

When lifting the toilet lid, be sure to be careful and handle it gently to prevent bumping.

For more complicated questions, the first thing you mean by "water level" is the water level of the water tank, or the water level in the pit? If it is the water level adjustment of the water tank, it is necessary to adjust the water inlet assembly, and there are n kinds of water inlet assembly, but as long as you study carefully, you can find that in the end, with the water level of the water tank, there is something similar to a pontoon that moves with the water level, and this pontoon can be adjusted, the higher the pontoon is adjusted, the higher the water level, and vice versa.

If you want to adjust the water level in the pit, you need to adjust the drainage assembly, it is recommended that individuals do not adjust, because the manufacturer is basically adjusted when leaving the factory, and the adjustable range is not large, it is difficult for non-professionals to adjust, the total achievement of drainage is to connect your fingers to control the flush button or lever, carefully observe and you will find that when you press the button or lever, there is a hole will open, the longer the opening time, the longer the drainage, the better the flushing effect, but also water; Now energy-saving toilets are two levels of water, both urine and stool, in fact, through the drainage assembly to control the drainage time to achieve the purpose of increasing and reducing the amount of water, the drainage assembly also has adjustable gears, but every time you adjust the water to test the flushing effect!

Popular science knowledge, how to adjust the water level of the toilet tank.

The management of ponds mainly regulates the temperature through the depth of the pond water. From more than 10 days to the germination stage, the water depth is maintained at 40 cm, and then with the vigorous growth of the branches, the water depth gradually deepens to 120 cm, and the water depth is reduced to 50 cm again one month before harvest.

Answer: Open the lid of the toilet tank first, find the thin leather pipe on the position of the water inlet valve inside the water tank, this thin leather pipe is generally inserted into the right drain valve, as long as the thin leather pipe is inserted into the central pipe, the water level in the toilet pit can be raised, if the thin leather pipe is pulled up, directly in the water tank, the water level in the toilet pit will be lowered.

It's not a toilet repair, but there's definitely one inside the toilet tank''Floats'', floating on the water. When the water supports the float to a certain height, the float closes the water pipe valve.

Therefore, to adjust the water level, it is mainly necessary to see how to adjust the connection device between the float and the water pipe valve.

2. Remove the water inlet and find the regulating valve that adjusts the water level inside.

3. Rotate the gear clockwise, you can make the water level rise, but the design of each brand is different, some are dialed up and down, if it is this kind of flush toilet, if you want to increase the flushing strength, you have to dial down, and lowering the water level is up.

Dial. 4. There is also a white cylinder in the water tank of some flush toilets, there will be different units on the cylinder, and the two blue gears can be adjusted to the size of the gear, and the upward adjustment is to raise the water level.

Answer: How to adjust the water level in the toilet: 1. If you want to lower the water level in the pit, open the water inlet valve on the left side of the water tank cover and have 1 thin leather pipe called the water supply pipe, which is generally inserted into the drainage valve on the right, and pull the right side up directly in the water tank, so that the water in the pit will not be too high when the water enters the water next time. 2. If you want to lower the water level in the water tank, there is a threaded rod at the top of the water inlet valve on the left, and the water level of the water tank can be lowered by twisting it counterclockwise, so that the water level of the water tank can be lowered when the water is added next time.

Or put a brick in the water tank, which can also play a role in saving water.

If you want to save water, you can put a mineral water bottle with water in the tank.