There are two living rooms at home, and one router can t cover it, how to install two routers?

Connect the second router with network fiber, the second router must not connect to the first router Do not connect the two routers together. The most important thing here is that you should never set the same IP address for the LAN port of both routers. Usually, this is the IP address used to log in to the router.

In other words, the two routers have to set different login addresses.

The WAN port of the main router is connected to the broadband in the fiber jack ternet access port 。The LAN port of the secondary router is connected to the LAN port of the primary router, and the secondary router acts as a wireless switch.

You can also configure the configuration of the main router according to the router's instructions and connect the wireless router. Configure the WAN connection mode. Some use the PPPOE dial-up model.

Some modems automatically dial up and obtain an IP address. Configure the SSID, encryption method, and password of the primary router.

To achieve cascade of two wireless routers, the key is the configuration of the secondary router, which must be configured as a wireless switch without using the routing function 。Go to the Standby Router Configuration page and configure the connection mode in AP mode.

To install a second router using a secondary router and a wireless switch, Router A must be placed in the multimedia information box 。If you put Router A in the living room, you have to cycle from Router A to the multimedia information box. Then, access Router B through the reserved network cable.

Two wireless routers are interconnected, often used to extend the coverage of wireless WiFi in the home, and the two wireless routers are connected in two ways: wireless bridging and wired connection. The wireless bridging method is subject to a lot of interference and the signal is unstable, so it is recommended to use the wired connection method.

The WAN port of the main router is connected to the broadband Internet port of the optical modem, the LAN port of the secondary router is connected to the LAN port of the main router, and the secondary router is used as a wireless switch. Configure the SSID, encryption mode, and password of the primary router.

The key to cascading two wireless routers is the configuration of the secondary router, which needs to be configured as a wireless switch without using the routing function. Go to the configuration page of the secondary router and set the connection mode to AP mode.

Set the management IP address of the secondary router and the same network segment as the primary router to facilitate the management of the secondary router. Disable the DHCP service of the secondary router, and the main router assigns an IP address to the home's network terminals. Set the SSID, encryption method, and password of the Fu router, which can be set to be consistent with the main router to achieve a certain degree of "wireless roaming".

If you want to connect seamlessly between two routers, use Pole Router Pole Satellite, I don't know if I haven't used other brands, for example, if you are playing a game, you use two routers to bridge it, and when the phone automatically switches to another router, you are 100% disconnected, Pole Route will not. The installation is also very simple.

If Router A is placed in the living room in these two ways, a loop needs to be made from Router A to the multimedia information box, and then Router B is connected to Router B through the network cable reserved indoors. The specific operation of secondary routing and wireless switches will not be repeated here, and a random search on the Internet will come out of a large number of tutorials.

The bandwidth network of 100M and below can be networked in the way of power modem, which is simple to install, as long as it is under the same meter, where the signal is not good, it can be plugged in, and the whole house wireless network coverage can be realized. In addition, it can also be networked through sub-parent routers or mesh.

If there are two living rooms in the home, or the overall area of the house is relatively large, two routers can be installed, but the premise is that the two routers cannot share a network cable

That is to say, a router can do a network cable for network coverage, if you say that you can install a router, you must embed a network cable broadband.

But now there is a device, they are also a kind of router, but they are not connected to the network cable, but just a small set-top box that is scattered out of a router.

The purpose is to receive the signal from the router and then send that signal out, but most of the time it is more expensive. Generally, a 200-square-meter family, a router with 4 antennas can basically be completely controlled, and there are many brands of routers in the market, I personally recommend you to choose TP-link.

Because I have also used a lot of router brands, I think this router is the most cost-effective, and the price is not too expensive, my house should be about 150 square meters, with 4 wires can be easily controlled,It's just that sometimes the contact signal is too poor when in the bathroom, after all, the bathroom is separated by several walls from the house where the router is placed.

The router must choose a better quality one, I chose a miscellaneous router before, after using it for half a year, the surface of the router has turned yellow, I thought it was discolored over time, in fact, the inside has been burned.

If there is no one at home, the consequences of burning the human body of this thing are really unimaginableBecause the router at home is basically supplied 24 hours a day and never loses power, sometimes we should also properly turn off the power to let the machine take a break.

One router can't cover, you can buy a signal amplifier for one router on it, you don't need to buy two routers.

You can install an amplifier, Huawei Pulian has this kind of thing, that is, plug this thing into the socket in another living room, which will amplify the wireless signal that you first routed!

There are two ways to connect two wireless routers: wireless bridging and wired connection, and it is recommended to use the wired connection method.

Set the IP address to not be on the same network segment as the IP address of the main router to facilitate access to the router settings screen later), and then click "Save".

Generally, one is installed in the master bedroom, and then one in the living room, and it is almost full coverage.

In your case, you can buy a mobile router like this, the one that doesn't need to be wired, and you can use it by plugging it in.

It's very simple to make two routers, and if you have a mobile company or a telecom company, you can install two routers in your home.

One is installed on the east side and one on the west side, so that the coverage is the whole house.

My normal would be to install a router outside the living room and a router in the bedroom.

From the router to that living room, connect another WIFI and you're good to go.

There are several ways to connect, both wireless and wired, depending on your own situation.

You can use two routers, two connections, maybe that's okay.

If you want to install two routers, you can usually set up the professional URL.

Buy a splitter and you can use it to install two routers.