-
Anonymous users2024-01-23Step 1: Prepare your tools first: screwdriver, wrench, pliers.
If it's just a replacement part (e.g. a seal), then have this part ready. Then close the main valve. Step 2:
Remove the small screws on or behind the faucet handle and remove the handle that is fixed to the faucet body. Some faucet screws are hidden under metal buttons, plastic buttons, or plastic sheets, and as soon as you open the buttons, you will see the handle screws mounted on the top. The screws of a faucet that have been used for a long time may become very tight due to rust and other reasons, and some lubricating oil can be dripped into it.
Step 3: If the screw is hidden in the hole, it is recommended to observe it with a flashlight first, mainly to see what the fixing screw inside is, the cross or a word, and then use the corresponding screwdriver to loosen. This screw of a few brands of faucets is an inner square hole (such as Moen), which is more troublesome to remove, and special care should be taken not to damage the screw mouth when using alternative tools.
When the screw is released, the handle can be removed. Step 4 of removing the faucet handle: At this time, what you see is a large copper nut, after removing the nut with a large wrench, you can remove the valve core of the faucet.
Observe whether the copper plane under the spool is uneven or whether there are fine sand grains, and remove it.
-
Anonymous users2024-01-22The procedure for disassembly is:
1. Turn off the main switch. Find the red and blue dots under the handle. Peel it open with your hand to reveal a small hole.
2. Use a flashlight.
Observe the hole to see whether a fixed screw inside is a cross or a slot, and use the corresponding screwdriver to loosen it.
A few brands of this screw have an inner square hole (e.g. Moen), which is a bit more cumbersome. When tools are not available, be careful not to damage the screw mouth with other alternative tools that can be removed.
3. When the screw is loosened, the handle can be removed.
Fourth, at this time, what you see is a large copper nut, after removing the nut with a movable wrench, you can remove the valve core of the faucet.
5. Observe whether the copper plane under the valve core is uneven or whether there are fine sand grains, and remove it. Remove the rubber seal on the flat surface and observe for damage.
6. Generally speaking, the integrity of the hot and cold faucet is good and the reliability is high. Therefore, after opening, it is often impossible to find obvious problems, at this time, it is just to change the valve core. The price of the spool ranges from 10-40 yuan.
7. Finally, install it in reverse according to the above procedures.
-
Anonymous users2024-01-21Tools: screwdrivers, wrenches and pliers. Here's how.
1.Remove the small screws on or behind the faucet handle, and then remove the handle that is fixed to the faucet body. A small number of faucet screws will be under the plastic buttons, metal buttons or plastic sheets, and as soon as the buttons are opened, you will see the handle screws mounted on the top.
For faucets that have been used for a long time or have not been used for a long time, its screws may become very tight due to rust and other reasons, if this happens, you can choose to drip some lubricating oil into it.
2.If the screw is hidden in the hole, it is recommended to use a flashlight to observe, which is mainly to see if the fixing screw inside is a cross or a slot, and then use the corresponding screwdriver to loosen. The screw of a few brands of faucets is an inner square hole, which is more troublesome to disassemble, and special attention should be paid not to damage the screw mouth when using alternative tools.
When the screw is released, the handle can be removed.
3.At this point, you will see a large copper nut, first remove the nut with a large movable wrench, and then you can remove the spool of the faucet. Observe whether the copper plane under the spool is uneven and free of fine sand particles, and remove it cleanly.
The procedure for disassembly is:
1. Turn off the main switch. Find the red and blue dots under the handle. Clasp it open by hand. >>>More
You look at the hot and cold water sign of the faucet, many faucets are a soybean-sized red and blue plastic block, there is a thread inside, you can remove the valve core with a flathead screwdriver, generally the faucet leakage is the valve core is broken, that is, there is a plastic head on the top of the plastic (the first picture with blue plastic), you can change the valve core to try. The valve core is not expensive, you try it, if it doesn't work, just change it to a new faucet, if you don't get someone to find someone to labor costs more expensive.
There are 2 hot and cold water pipes, and the corresponding outlet pipes are also 2, which can be connected to each other.
The kitchen faucet hose is generally the first to fix the faucet of each part of the rubber pad, from top to bottom into the hole of the water cold, and then use a hollow flange child near the bottom of the faucet at the end of the faucet to tighten the connection with the disc body is strong and firm, and then tighten the interface at the bottom of the hose clockwise.
Please buckle the red and blue logo on the valve, remove it with a screwdriver, and then you will understand how to open it.