The toilet is clogged with feces, and now the is full, what to do

The initial decoration of the bathroom is very important, because the decoration at this time should take into account the problems of waterproof, odor prevention and so on. Many people find that soon after installing the toilet, it will smell, why?

This is what my toilet base looks like after it is disassembled, it has been smelly for three years, so disgusting.

Let's talk about the four main reasons why the toilet stinks:

1. The quality of the toilet product itself is poor, and the void of the toilet is large, and there are a lot of stains left in it.

2. The project was not done well during installation, and the flange ring under the toilet was not sealed.

3. The base of the toilet is not sealed, or the glass glue of the base is not done.

4. There are some firing holes in the toilet base, but these holes are not sealed, and the smell comes out.

The solution of Article 1 is that we can only buy toilet products with better quality, and we can buy better glazed products.

Article 2 suggests that you should use glass glue for the flange, and when you use this kind of glue, you should use water to flush it with water to see if there is any leakage.

Article 3 Most of the toilets that we sleep on now do not use cement to seal the bottom, most of them use glass glue, and we must pay attention to not break it when playing glass glue, and we must play it completely in a whole circle.

The base of the fourth toilet bowl usually has two or three firing holes, and many people don't know about it. Some merchants do not treat the product when it leaves the factory, so after you install it, the smell of the toilet will flow out of the holes here, so we have to seal these holes.

This small suggestion, in fact, installing a toilet is a kind of technical work, even if the worker is skilled, it is not as good as installing it yourself. When you buy a product, you can also let the merchant package install it, so that you can save the installation fee.

It should be noted that if you want to lay the floor tiles and then install the toilet, this is the correct installation sequence.

1. Don't be impulsive if you find a clogged toilet.

Generally, many people find that if they flush but do not get water, they will flush it a second or third time, which is a wrong move! If you can't flush the first time, stop flushing, as this will cause more water to fill the pot. The first flush will not cause the toilet basin to overflow, but the second flush might.

2. Turn off water sources.

There are two ways to turn off the water source, one is to turn off the entire water supply system in your home, but in this case, you need to clean the water in the water pipes in advance, otherwise you may end up with water everywhere. The second method is to see if the toilet has a toilet angle valve, and if an angle valve is installed, you can simply close the toilet angle valve.

3. Smell and keep ventilated.

Make sure the toilet is well ventilated. Open your ventilation or windows to minimise foul odors and avoid inhaling too many potentially toxic gases from any chemical products you may be using.

4. Pour in detergent and hot water.

Pour in a little dishwashing detergent. Pour a few drops of dishwashing detergent down the toilet. Pour a basin or half a bucket of hot tap water from waist height into the toilet basin.

The reason for pouring water from waist height is because this high level of water can help unclog blockages or flush away corrosion. The temperature of the hot water is like the temperature of the usual tea, and there is no need to boil the water, because too hot water can break the ceramic.

Too little water is also not effective, because you need to let the temperature of the water flowing into the toilet or slapping in the blockage rise. Leave the water and dishwashing detergent on the toilet sink for a while. Sometimes this will allow the blockage to soften, loosen, and then clear itself.

5. Wait for the water to be flushed.

After waiting for the blockage to soften and loosen, we can directly flush the toilet. If the water cannot flow into the toilet, it means that the blockage is not dissolvable, and it is recommended to find a toilet repair master to unclog the toilet at this time.

You can use a leather picker, but you need to squeeze out the air in the skin bag first. The method is to put the skin bowl below the water surface in the toilet, press hard to squeeze out the air, and then aim the skin bowl at the drain (pay attention to the skin bowl should not show the water surface), and suck it repeatedly until the feces leak down. It can be repeated several times.

Poke it with a wire yourself, and if you can't get started, you will find a property.

Get straight to the ground and don't trust which of them

1. Don't be impulsive if you find a clogged toilet.

Generally, many people find that if they flush but do not come out of the water, they will flush the second or third time, which is a wrong move! If you can't flush the first time, stop flushing, as this will cause more water to fill the pot. The first flush will not cause the toilet basin to overflow, but the second flush might.

2. Turn off water sources.

There are two ways to turn off the water source, one is to turn off the entire water supply system in your home, but in this case, you need to clean the water in the water pipes in advance, otherwise you may end up with water everywhere. The second method is to see if the toilet has a toilet angle valve, and if an angle valve is installed, you can simply close the toilet angle valve.

3. Smell and keep ventilated.

Make sure the toilet is well ventilated. Open your ventilation or windows to minimise foul odors and avoid inhaling too many potentially toxic gases from any chemical products you may be using.

4. Pour in detergent and hot water.

Pour in a little dishwashing detergent. Pour a few drops of dishwashing detergent down the toilet. Pour a basin or half a bucket of hot tap water from waist height into the toilet basin.

The reason for pouring water from waist height is because this high level of water can help unclog blockages or flush away corrosion. The temperature of the hot water is like the temperature of the usual tea, and there is no need to boil the water, because too hot water can break the ceramic.

Too little water also doesn't work, because you need to get the water flowing into the toilet or slapping in the clogged water to raise the temperature. Leave the water and dishwashing detergent on the toilet sink for a while. Sometimes this will allow the blockage to soften, loosen, and then clear itself.

5. Wait for the water to be flushed.

After waiting for the blockage to soften and loosen, we can directly flush the toilet. If the water cannot flow into the toilet, it means that the blockage is not dissolvable, and it is recommended to find a toilet repair master to unclog the toilet at this time.