The process of solid wood furniture painting

Varnish process:

1. Apply coloring oil or toning oil. (Note: For projects with discoloration requirements, this process is not required for ordinary projects).

2. Brush the varnish to protect the primer. (If there is no one process, it is a process.) If the varnish is to be painted in the original color, the surface must be cleaned and the protective primer applied immediately after the material is purchased on the site.

Primers are generally topcoats. Note: The varnish finish must be applied before the wall paint is painted.

3. Clean up the dust and dirt on the surface of the wood.

4. Use sandpaper to polish the surface of the board or wood line.

5. Brush all over the paint.

Wooden at least 5 times, sanded with water sandpaper, faded, waxed, polished. Note: Interval until dry. 6 hours in summer and 24 hours in winter. The site is kept clean and free of dust. The temperature is above 5 degrees Celsius.

1. The general steps of product production; Preparation.

Raw processing and molding paint assembly.

Preparation: From logs to boards, etc. Including the cooking and sterilization of the wood, and then drying to about 8% 12% of the water content and water content before the oven can be used.

Raw processing: forming product wood embryo workpiece; Including: material cutting, cutting, planing, planing and other processing processes.

Molding: Fabrication into parts that conform to various design shapes.

2. The production process of solid wood furniture: cutting materials (straight materials, bending materials), planing teeth, joint teeth, mechanical processing, installation, secondary drying, paint packaging, warehousing, mechanical processing: including gong machine, tenoning, punching, grinding and other processing processes.

3. Introduction to the production process of panel furniture: cutting cold-pressed fine saw, edge sealing, rowing, nailing, trial installation, paint packaging, warehousing, 4, solid wood furniture painting process: A, Tianyuan Yazhu (19 series) paint process:

The white billet contains the platform, spray the first primer (to dry for 2 hours), hit the first oil mill, manually rub the color (three times), and spray the second primer (to dry for 3 hours).

Coloring oil grinding oil (waiting for drying hours) packaging B, Yaming (16 series) paint process: white billet with platform spraying the first primer (to dry for 3 hours) manual rubbing and priming color grinding including platform spraying the second primer (to dry for 3 hours) oiling grinding color repair (to dry for 3 hours) color oil grinding oil (to dry hours) packaging.

The process of solid wood parts refers to changing the shape, size or physical properties of raw materials through various processing equipment, and processing raw materials into technical conformity.

When a product is requested, the sum of a series of work carried out is called a process.

It consists of several processes:

Drying, batching, wool processing, gluing processing, bending processing, net material processing, component assembly, component processing, general assembly, finishing.

Wood paint is different according to the different lacquer, the process is different, first, the varnish process.

1. Coloring oil or toning oil (note: limited to projects with discoloration requirements, ordinary projects do not need this process).

2. Brush the varnish to protect the primer (if there is no 1 process, this is the first process).

If the varnish is to be painted in the original color, the surface must be cleaned and the first protective primer applied immediately after the material is purchased on the jobsite. Primers are also generally topcoats.

Note: The varnish finish must be applied before the wall paint is applied.

3. Clean up the dust and dirt on the surface of the wood.

4. Use sandpaper to polish the surface of the board or wood line.

5. Brush the paint for the first time.

6. After drying, use the blended toner, cooked rubber powder, and double fly powder to make putty to cover up the nail holes and tree scars, so as to make it the same as the color.

7. After drying, use fine sandpaper to polish the rough part of the toner, which is very important.

8. Brush the paint again.

9. After drying, polish with fine sandpaper.

10. Brush the paint.

That is, after a coat of paint, add a fine sandpaper to polish, and so on. If there is a special primer, change the first coat to a special primer.

11. Wipe the surface of the wood with a damp cloth, and then polish the surface after wetting the water with sandpaper, commonly known as water grinding.

12. Brush the last coat of paint.

Generally speaking, counting the last coat of paint, you need to brush the topcoat 4-8 times to have a better effect. The more coats of paint, the better, but generally not more than 10 times. When the paint film is constructed in wet weather, the paint film will be whitish, which can be eliminated by adding a diluted dose of 10%-15% nitro magnetized white water.

Second, the oil mixing process.

1. Clean the dust and dirt on the surface of the wood first.

2. Mix the surface of the full batch of woodware with pig blood ash and double fly powder.

3. After drying, polish with sandpaper.

4. Brush the paint for the first time.

5. Make up for the defects.

6. After drying, polish with sandpaper.

7. Brush the paint for the second time.

8. After drying, use sandpaper.

9. Brush the paint for the third time.

Generally speaking, it is advisable to mix oil 2-3 times.

Varnish construction process: Clean the surface of the wood Sandpaper polish on the moisturizing powder Sandpaper Scrape the first putty, sandpaper polish Scrape the putty for the second time, fine sandpaper polish Brush the oil color Brush the first varnish Spell the color, refill the putty, fine sandpaper polish Brush the second varnish, fine sandpaper polish Brush the third varnish, polish the water sandpaper sandpaper sanding and fade, wax, polish.

Mixed color paint construction process: first sweep the dust on the surface of the base layer, repair the base layer, flatten it with frosted paper, paint the scar at the knots, scrape the putty at the base, apply dry oil, scrape the putty for the first time, polish it, paint the base coat, paint the bottom coat, dry and hard, paint the top layer, repair the putty, polish and wipe the third topcoat, apply the second coat, polish the third topcoat, polish and wax.

I don't know about this. I only know furniture paint.

I used it 2 days ago.

Jinweida paint is good.

Content from user: Jaezi Text.

1 Main construction technology (1) varnish construction process: clean the surface of the wood, matte paper polishing, moisturizing powder, sandpaper sandpaper, full scraping of the first putty, sandpaper polishing, full scraping of the second putty, fine sandpaper polishing, painting oil color, brushing the first varnish, spelling the color, recovering the putty, fine sandpaper polishing, brushing the second varnish, fine sandpaper polishing, brushing the third varnish, polishing water sandpaper grinding fade, waxing, polishing. (2) Mixed color paint construction process:

First sweep the dust on the surface of the base layer, repair the base layer Flatten it with frosted paper Paint the scars at the knots Primer scrape putty Apply dry oil Scrape putty for the first time Polishing Brush the primer Dry and hard primer Brush the top layer Repair putty for repair Polishing and wiping the third topcoat Paint the second coat Polishing The third topcoat Polishing and waxing. 2 construction points: The construction specification of clear oil brushing is an important process for painting varnish, and the dust, oil and other impurities on the surface of the wood should be removed first.

Lubricating oil powder is also an important process of varnish painting, during construction, cotton silk is dipped in oil powder and smeared on the surface of the wood, rubbed back and forth with your hands, and the oil powder is rubbed into the eye of the wood.

When brushing the clear oil, hold the oil brush easily and naturally, and gently press the fingers to ensure that the brush does not loosen or fall off when moving. When brushing, it is necessary to follow the requirements of dipping more secondary, less dipping oil each time, operating diligently, and brushing smoothly, in accordance with the order of first up and then down, first difficult and then easy, first left and then right, first inside and then outside, and the operation method of horizontal and vertical brushing.

When the construction specification of the base layer treatment of the wood surface oil mixture, in addition to cleaning up the debris of the base layer, the local putty embedding nitro paint 5 should also be carried out, and the other method is to directly sweep the imitation red copper paint on the black top coat, and the imitation red copper effect can also be obtained, and this effect makes the wrought iron products appear to be the operation method of the simulated painting effect of wrought iron handicrafts.

I don't know how to copy the furniture of the house you bought.

Generally, good brand solid wood furniture will have regular after-sales maintenance, as if it is maintained with something called turquoise beads.

Also, don't wipe with a wet rag, don't wipe with harsh detergents, ventilate, and keep a relatively stable temperature and humidity in the room.

The furniture is not so expensive, or pay attention to it every day, how to use it, just pay attention to the cleaning.

Go to the United Family Mall and do some. Finish. Untie.

Good. up, this. Family.

Target. United Family Furniture, just. Raise.

Supply. Stick. Heart.

Target. Furniture set. System.

Wear. Servant. Product.

The quality is the most. Okay, set. Plan.

Very. Alone. Special. Target.