How to change the bathroom light when it is broken.

Because the lights in the toilet are basically put together with our bath bomb, it is necessary to buy a special lamp when replacing it. As long as this good group lamp is sold in any hardware store, and then open the lid of our bath bomb, its 4 corners will be unscrewed or 4 screws of orange socks, and then the bad lamp is unscrewed, the good lamp is installed, and then the cover on the bath bomb can be buckled.

Toilet does not refer to a toilet alone, but is a collective term for toilets, toilets, and baths. According to the layout, the toilet can be divided into three types: independent, part-time and compromise. According to the form, it can be divided into semi-open, open and closed.

At present, it is more popular to distinguish between dry and wet partitions. Residential bathrooms are generally divided into dedicated and communal. The dedicated one serves only the master bedroom; The common ones are connected to the public walkways and are shared by other family members and guests.

Suck the corner of the side gusset with a suction cup and take it out.

Send a picture to see it clearly.

1. First of all, the power should be cut off, so that there is no power when it is replaced, so it is necessary to choose a bright light when it is replaced, or a ruler spine can also be used to play a flashlight.

2. Disassemble the integrated ceiling plate around the integrated ceiling set, expose the keel, look for the terminal, unplug the ceiling lamp and the blind connection of the terminal, and sort out the wires of the ceiling;

3. The infiltration method of removing the gusset plate: use two harder plastic cards, insert the corners of the gusset plate, move the card to the other end, pry a little bit of the gap down with a little force, and cut out the gusset by hand. (It's like unlocking a door with a plastic sheet).

Embedded tank alarm ceiling lamp: Embedded ceiling lamp is mainly installed inside the integrated vertical cover ceiling, this kind of lamp is more troublesome if it is broken to replace, because its internal structure is more complex than the signal, remember to cut off the power supply before disassembly.

As we all know, in the decoration of the bathroom, the installation of lamps and lanterns is a crucial link. However, we all know that most families now install some ceiling lights in their bathrooms, because these ceiling lights are used very frequently, so damage is a very common phenomenon. So, how to change the bathroom light when it is broken?

Let's explore it together!

1.In fact, it is relatively simple to replace the ceiling light in the bathroom. The first step you have to do is to buy the original lamp or the same lamp model as the original bulb.

The next step is to change the operation. However, before replacing, all power must be turned off, the main purpose of which is to ensure your own safety.

2.I believe we all know that most of the ceiling lights in the bathroom are embedded ceiling lights. Therefore, we only need to disconnect the ramp of the power supply, and then remove the gusset on the side of the ceiling lamp, and then take down the gusset on each side around the ceiling.

Then take off the lampshade, and take the same type of lamp tube to install it, but also remember to install the lampshade, and finally turn on the power to see if the lamp can emit light normally, and then buckle the ceiling buckle plate on it.

3.Once you've tested it a few times and made sure there's no problem, you can snap the gusset on the ceiling. But there is a caveat:

1.When installing the bathroom light, you must clearly remember the direction you removed at that time, and when resetting, you must also install it in the previous direction. 2.

When you take the gusset and lampshade, you must be cautious, and be sure to follow the rule of "take it lightly", so as to avoid the deformation of the gusset and lampshade, which eventually leads to the phenomenon that there is no way to reset.

Summary: The above introduced to you how to replace the bathroom light when it is broken, and I hope to give you some help. If you want to know more about the installation of lamps and lanterns, you can continue to lock our website, and the follow-up content will be richer!

It depends on what kind of light you have, is it an ordinary energy-saving lamp, or a ring light, an LED light, or some other type of light? In general, there is a high possibility that the bulb or tube will be broken, so you can only replace these without replacing all of them. Or if you go to the picture, I'll help you see what you need to change.

Open the lampshade from one side, use a small screwdriver to extend the edge of the length side and pry open the gap and stretch it downward, and then open it, take a look at the model of the lamp or take a picture to the store to buy it and replace it.

Take a ladder up to see what the tube looks like, or take it to the hardware store and ask what kind of tube it is.

How to replace a broken bathroom light

1. Turn off the power.

> when replacing the lamp, you can press the switch to turn off the ceiling light. Or we turn off the electric switch in the bathroom so that it is in a safe environment where the power is off.

2. Remove the lampshade.

> when removing the lampshade, you can first remove a piece of the gusset around the lamp. We use a knife to pry it down along the gap of the gusset, and after prying out a part of the gusset, we can pull it off with our hands. Next, hold the edge of the lampshade and remove the shade.

You can also pry the lampshade off directly with a knife or suction cup.

3. Replace the lamp.

After removing the lampshade >, unplug the wire on the lamp tube, and then break the buckle to remove the lamp. If it's a square tube, we can just unplug it. Everyone prepares the new lamp, and the model size of the new lamp should be the same as the old lamp.

Then fix the lamp to the lamp and plug the wire connector of the ballast into the lamp connection.

4. Replace the ballast.

> after the lamp is replaced, if the lamp still does not work properly, it means that the ballast of the lamp is faulty. We can see that there is a wiring port on the base of the lamp, we loosen the screws of the wiring port to pull out the two wires of the ballast, and then unplug the wire wiring connector at the lamp.

Next, use a screwdriver to loosen the fixing screws and remove the ballast. Finally, prepare a new ballast, fix it to the base of the lamp with screws, and connect the wires. After the lamp was replaced, we fixed the lampshade with the base.

Unscrew the bad bulb and buy a better one and screw it on the same size as his.

When replacing the ceiling lamp, be sure to pull out the plug, and then pull out the plug on the rectifier, which must not be hard, or will not damage the accessories of the lamp, and then just remove the old lamp and install the lamp, clamp it with a circlip, and then plug in the filament at both ends of the rectifier plug lamp.

First remove the original and then take it to the hardware store to match a suitable lamp, the current lamp disassembly is very convenient, now most of them are gusset lights, the gusset next to the lamp should be able to take out the original lamp.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose:?bdfc

1. When replacing, you can use the fixing screws around the round suction cup of the screwdriver to remove them first, these small screws are used to fix the dry lead of the outer iron ring of the lampshade, and then rotate the round suction cup, that is, the lampshade, to rotate and unscrew the bulb to remove the damaged bulb inside, install the bulb of the same model, and finally reinstall the lampshade.

2. The buckle structure of the embedded ceiling lamp is more complex, you can not use brute force when dismantling, you can carefully observe the situation around the buckle, it is stuck with a spring clip, you only need to press and then gently break it down to replace the bulb, after replacement, remember to reinstall the outer cover.