What is the difference between waxing and hot wax in mahogany furniture?

1. The operation is different

Waxing needs to be carried out in strict accordance with a series of steps such as boiling, baking, scraping, wiping, etc., while waxing is only to wipe the wax on the furniture with tools.

2. The time is different:

Waxing usually takes a while and is a very careful process, while waxing usually takes only one or half a day.

3. The duration is different:

1) With the passage of time, this protective film is constantly affected by factors such as air oxidation, human hand touching and wiping with rags, so that the surface, edges and edges of the furniture appear a natural, translucent, warm and moist surface form.

2) Waxing is to rub wax on the surface of wood, and after one or two months of use, it will gradually disappear.

Waxing is a modern process, and waxing is an ancient process. The waxing time is short, and the waxing time is complicated.

1. Traditional waxing needs to be carried out in strict accordance with a series of steps such as boiling, baking, scraping, and wiping, while waxing only needs to wipe the wax on the furniture with a cloth many times.

2. Traditional waxing usually takes a few working days, while waxing usually only takes a minute or two or even a few minutes. The time difference between the two is many times.

3. The hot wax can penetrate into the wood, and the wood eats the wax deeply. A standard wax can last for more than 10 years.

4. Waxing is to rub wax on the surface of wood. The surface of the furniture looks shiny, but there is no wax in the wood. So, after a month or two of use, the wax on the furniture is gone. Some of the wax will be gone after a few days.

Waxing is modern.

Process, hot wax is an ancient process. Waxing takes a short time, the process is simple, and the waxing takes a long time and the process is complicated.

1. Traditional waxing needs to be strictly carried out according to a series of steps such as boiling, baking, scraping, and wiping, while modern waxing is just rubbing the wax back and forth on the furniture with a cloth several times.

2. Traditional waxing usually takes several working days, while modern waxing often takes only one or twenty minutes or even a few minutes, and the time spent on the two is many times different.

3. The hot wax can penetrate the wax into the wood, and the wood eats the wax deeply, and the maintenance effect of a more standardized hot wax on the furniture can be maintained for more than ten years.

4. The wax is to rub the wax on the surface of the wood, the surface of the furniture looks brighter, but the wood does not eat wax at all, so it is often used for a month or two, the wax on the furniture is gone, and some even after a few days the wax on it is gone.

1. In terms of operation, the traditional waxing needs to be strictly carried out according to a series of steps such as boiling, baking, scraping, and wiping, while the modern waxing is just a few times to wipe the wax back and forth on the furniture with a cloth.

2. In terms of time, the traditional waxing usually takes several working days, while the modern waxing often takes only one or twenty minutes or even a few minutes, and the time spent on the two is many times different.

3. The hot wax can penetrate the wax into the wood, and the wood eats the wax deeply, and the maintenance effect of a more standardized hot wax on the furniture can be maintained for more than ten years. The wax is just to rub the wax on the surface of the wood, the surface of the furniture looks brighter, but the wood does not eat wax at all, so often after one or two months of use, the wax on the furniture is gone, and some even after a few days the wax on the top is gone.

Wax process: Wax is generally made of beeswax, if there is no wax, it can also be used as white wax for candles. When scalding wax in a small area, you can hold the wax block in one hand, and melt the wax block with an electric soldering iron or soldering iron in the other hand, and drop or coat it on the surface of the wood to form a thin layer.

If a large area of wax is scalded, this process can also put the wax block into a metal container to heat and melt into wax liquid, and then use a brush or spoon to coat or pour the wax liquid onto the wood, which can greatly speed up the efficiency. Then iron the wax layer with a soldering iron, and use heat to make the wax liquid penetrate into the wood grain, this process is the most important, first, the wax liquid must be fully melted, and the heating time must be properly maintained; The second is not too much, to not burn the wood fiber as the degree. After all the ironing is done, wipe off the floating wax with a slightly thicker dry cloth, and then you can use an electric hair dryer to heat the surface slightly, so that it is easier to wipe off the floating wax.

Finally, the wood is fully wiped with a clean cloth, and so far, the scalding process is completed.

Waxing process: The wood ready for waxing is thoroughly sanded and coated with a layer of diluted insect paint as a primer before waxing. When the primer is completely dry, you can use 0000 steel wool to sand along the wood grain; Then clean the furniture thoroughly with a dipped cloth.

You can use a clean, non-plush cloth pad to coat the wood with a thin layer of solid wax.

2. When waxing, apply a thin, uniform layer of wax in a circular manner. Apply wax only in a small area at a time. Some manufacturers recommend using a damp (not soaked) cloth pad.

3If you use water, make sure the surface of the furniture is dry before you polish it. As the manufacturer advises, you should allow the wax to dry completely. Then use a clean cloth and vigorously wipe the wax layer to wipe off the excess wax.

4. When the wax layer is uniform, polish it with a clean cloth. Like above, apply two to three coats of wax to complete the surface finish. When laying a layer of wax, you should polish each previous layer completely.

The waxing of mahogany furniture refers to a method of surface treatment, hot wax and baking wax are the specific process of waxing, and the waxing of mahogany furniture must be done by hot wax or baking wax, and there is no effect on waxing without heating, so waxing refers to the treatment method, hot wax and baking wax refer to the specific process. Thank you.

The essence of mahogany furniture is that it is not embellished with any paint, but the process of waxing is used, and the woodiness of the wood itself and the beautiful wood grain are adhered to. Waxing is divided into open waxing and closed waxing. Open waxing is to expose the wood eye (needle eye) and wood grain of the wood to the outside, and the wood with good information and the products with high technology level are generally selected for open waxing, so as to show the level of handicrafts.

Closing waxing is to fill the pores of the wood eye (needle eye) to enhance the lubrication feeling, ordinary lacquer, because the lacquer is environmentally friendly, non-toxic and tasteless. When filling pores, beeswax is used to wax, first bake the wax into the wood with high temperature, then bake it into the wood with an electric heater, and finally use soft cotton cloth and cotton yarn to wipe off the remaining wax.

There are five major pleas for waxing. 1. Color: The waxing is bright, the wax film is very thin, the appearance of the wood is not polished, but the waterproof is good, the wood is not easy to crack, and it plays a closing role, so the selection of wood is higher, and the ordinary color is even.

2. Luster: waxing is not as bright as paint, because the brightness is determined by wax, the product is carefully polished and polished and the polishing of wax still has excellent gloss, but ordinary customers do not seek this role. 3. Lubrication:

After careful polishing (Yiguxuan classical furniture), the effect is determined by the thickness of the sand and the thoroughness of the polishing, the sandpaper through the process of 180 ->320 ->1000 from coarse to fine, and finally polished with a fine cotton ball, forming a bright and translucent luster and soft feel. 4. Fullness: There are two kinds of open and closed to choose from.

5. Clarity: leak out the original wood grain. It is also important to note that the baked wax must penetrate the wood thoroughly, and the temperature of the heat gun must not be too high during the entire operation.

Furniture products should not be scalded, and they need to be carefully maintained.