How do you quickly clean kitchen grease? How is the kitchen clean

Cooktop It is best to soak it in hot water first to soften the dirt on the cooktop, then spray it with detergent and wipe it clean with a rag.

Sink Grab a handful of fine salt, sprinkle evenly on the walls of the pool, and then rinse it several times with hot water from top to bottom to remove the oil. The grooves in the four corners of the pool can be brushed with a waste toothbrush dipped in some fine salt grains, or you can sew a small pocket with old cloth, put a few pieces of discarded soap heads, soak in a little water, brush the oily places on the inner wall of the pool a few times, and finally rinse with clean water, and the oil will be gone.

Refrigerator If the refrigerator is white, it will turn a little yellow due to oil stains over time, so you can use a soft cloth dipped in a little toothpaste to wipe it slowly. The more difficult crevices on the side of the refrigerator door can be cleaned with an old toothbrush.

Stainless steel pans Stainless steel pans are prone to black dirt and are difficult to scrub. Add about half a pot of water to the larger pot at home, add some pineapple skin, and then put the smaller pots one by one, heat and boil on the stove for a while, and when they are cooled, you can find that these pots will be as bright as new.

Casserole If there is dirt in the casserole, you can pour some rice soup into the pot and soak it to heat, then use a brush to brush off the dirt in the pot, and finally rinse it with water. If the casserole is stained with oil, you can use the leftover tea residue to wipe the surface of the casserole several times to wash off the grease.

To clean the claypot, pot or stove, wet the bottom of the pot, burnt food and stains on the stove with warm water and sprinkle plenty of baking soda before leaving them overnight. In this way, the burnt food and stains are sufficiently softened and can be easily removed with a soft brush.

To clean stains in a tea or coffee cup, apply a damp cloth with a small amount of baking soda and rotate the cloth repeatedly inside the cup to remove the tea or coffee stains in the cup.

When cleaning sinks and kitchen cabinets, sprinkle baking soda, borax powder or washing soda on these areas first. Then wipe back and forth with a damp rag. It doesn't take much effort to wipe all the stains off. Brush the dishes with grease stains, and wash them with a cloth or loofah.

Personally, I think that the kitchen is very good, the things do not smell strange and do not hurt your hands, it turns out that when you use Vermeer and other products, you still burn your hands and choke on breath, this is really good.

You can use the kitchen to clean it, it doesn't hurt your hands at all, and it doesn't smell choking, it's really good.

(1) Remove the cylinder head cover of the diesel engine in the cold car state;

2) Rotate the flywheel so that the top dead center engraved line on the flywheel is aligned with the pointer engraved line on the water tank, so that the piston is in the top dead center position of the compression stroke;

3) Measure the gap between the tail end of the valve stem and the rocker arm with the gauge, if the gauge cannot be inserted or there is still a large gap after insertion, the valve clearance needs to be adjusted. When the S195 diesel engine is cold, the intake valve clearance is and the exhaust valve clearance is.

4) Loosen the lock nut of the valve clearance adjustment screw, twist the adjustment screw, measure with a thickness gauge until the measured value is consistent with the specified value, and tighten the lock nut while keeping the adjustment screw immobile.

5) When the intake and exhaust valve clearance is adjusted, shake the crankshaft several times, and then measure its clearance, if there is any change, it should be readjusted.

Diesel engine valve clearance adjustment steps:1Before the valve clearance adjustment, remove the cylinder head cover first, and then rotate the crankshaft to make the timing "0" scale mark on the flywheel, and the diesel engine low cylinder is at the top dead center at this time; 2. To confirm which side of the cylinder at the top dead center is at the beginning of the expansion stroke, two methods can be used, a. the side cover plate of the fuel injection pump can be removed, and whether the plunger spring of the injection pump is in a state of compression b. slightly rotate the crankshaft to observe whether the intake and exhaust valves are in a stationary state 3. Adjust the valve clearance 4. Use a wrench and a screwdriver to loosen the lock nut and adjusting nut nail on the rocker arm, and insert the thickness gauge directly into the rocker arm valve according to the specified clearance, and then twist the adjusting screw for the certificate. When the rocker arm and valve are in contact with the gauge, the nut can be tightened when the gauge can still be moved, and finally the gauge can be moved again to check once.

5. After adjusting the valve by the above method, rotate the crankshaft 360 degrees, and complete the skipping of the valve clearance by adjusting it in two times.

Usually the kitchen utensils at home are cleaned with Weiwang's 10-effect all-round kitchen cleaner. Detergents can help remove grease from kitchen utensils when cleaning them, and the sterilization rate is as high as when cleaning.

Take the 4100 diesel engine as an example:

You can use the valve clearance adjustment method twice, that is, you can complete all the valve clearance adjustment by rotating the crankshaft twice, such as the 4-cylinder machine in the order of work, open the cylinder cover cover, rotate the crankshaft, and see the 4-cylinder valve movement, when the intake and exhaust valves have overlapping movements, it is the exhaust top dead center of the 4 cylinders, at this time the 1 cylinder is in the compression top dead center, you can adjust the intake and exhaust valves of the 1 cylinder, the intake valve of the 2 cylinders, and the exhaust valves of the 3 cylinders, these valves are absolutely closed.

Then rotate the crankshaft 360 degrees, find the compression top dead center of the 4 cylinders according to this method, and adjust the rest of the valves. When adjusting, while tightening the adjustment screw on the valve rocker arm, insert the valve stem end and pull back and forth between the rocker arm with a thick gauge, feel a slight resistance, and then check again until it fits.

Adjust the piston corresponding to the cylinder to the top dead center, and then see the best range of exhaust valve clearance according to the maintenance manual, and then select the corresponding thickness of the feeler gauge to be stuffed between the top of the valve and the elephant's foot, and then tighten the adjustment screw, turn the flywheel and then plug the feeler gauge in, and reach the state of plugging and withdrawing with slight resistance.

Then adjust the other cylinders in turn according to the firing order.