-
Anonymous users2024-01-23First prepare a movable wrench, Phillips screwdriver, the specific steps are as follows:
1. The first step is to close the valve on the washstand.
2. In the second step, use a movable wrench to remove the screws connecting the sewer pipe to the faucet.
3. In the third step, use a wrench to disassemble the screws that fix the faucet, and then remove the damaged drain.
4. The fourth step is to fix the new drain you bought at the position where it needs to be installed, and remember to install a rubber pad under the water pipe mouth to play the role of waterproof sealing.
5. The fifth step, then use a wrench to tighten the screws under the faucet and connect the water pipe.
6. Finally, the installation is done.
-
Anonymous users2024-01-22Prepare a movable wrench, Phillips screwdriver, the detailed operation process is described below:
1. First close the valve under the washbasin.
2. Then use an adjustable wrench to remove the connecting screws between the water pipe and the faucet.
3. Remove the two screws that fix the faucet.
4. Then remove the bad drain.
5. Put the new nozzle in the installation position, and put a rubber pad on the water nozzle to use for waterproof sealing.
6. Then tighten the screws under the faucet and connect the water pipe.
7. Finally, the interface installation is completed.
-
Anonymous users2024-01-21, kitchen sink drain pipe installation step 1: install the drain filter basket.
When installing the sewer pipe under the filter basket, the main attention should be paid to the connection between the sewer pipe and the tank, which should not only be firm, but also sealed. Generally, the sink has two filter baskets, and the installation method is the same.
Kitchen Sink Drain Pipe Installation Step 2: Install the sewer main.
Usually people will buy a sink with two filter baskets, the distance between the two sewer pipes is close and far, the installation of the sink sewer main in this case is more complicated, and the installation of the bathroom installation master will cut the matching drainage pipe according to the actual situation, at this time, it is necessary to pay attention to the sealing between each interface, and the common water leakage problem occurs at these joints.
Kitchen sink drain pipe installation step 3: overflow drain pipe installation.
First tell you what is the overflow, the overflow is located in the sink or basin side below the countertop to prevent the overflow of water after the overflow, so it is called the overflow, the overflow sewer pipe installation first assemble the sewer main, and then connect the basin overflow sewer pipe outlet to the sewer main, the other end is connected to the back of the kitchen sink overflow, spiral tightening (before the interface is connected, the raw material belt should be wound first).
Because the bathroom installation is more complicated and too difficult, you can consider asking a professional bathroom installation team to help, I hope it will be useful to you
OK. However, it is best to have some slope to allow for smooth drainage. If you walk directly on the ground, you need to pay special attention in the future, and you can't drain any residue out of this pipe, otherwise it will easily cause blockage.
How far is the original kitchen from the balcony, if not, you can direct the water from the balcony to the original kitchen!
Start by identifying where the water is leaking. If it is only a joint leakage, under the premise that the quality of the pipe is qualified, the joint can be replaced or a leak-proof sealing tape and AB sealant can be added to the joint; If the quality of the pipe is not good, the pipe should be replaced. You can also apply the adjusted AB glue in the leaking place, and then wrap a layer of ribbon on it, so that the ribbon is soaked with AB glue and then apply a layer of AB glue on the ribbon, and the whole process can be divided into two or many times.
1. Cast iron sewer pipes in the bathroom.
There are several ways to repair the rupture: it is best to start at the interface and replace it with a new section of pipe. You can also try to weld the cracked area, and if the cracked joint is small, you can also lay it with quick-drying cement until there is no water leakage. >>>More
Use brickwork to ensure the pipe.
Using bricks to ensure management is the first method used, because it is used on the surface of the brick and then cement plastering, and then paste porcelain blind bricks or something, generally speaking, the sound insulation effect is good, but it takes up more space. >>>More