What kind of machine do you need to make panel furniture?

In fact, it is the same as solid wood furniture to use a lot of woodworking machinery, such as cutting saws, gong machines [engraving machines] for modeling, and small band saws for bending materials. . . To do disassembly and assembly, it is necessary to drill and open the tenon machine. There are also veneer splicing machines and hot presses...

The factory building depends on the size you want, generally about 500 square meters. The investment in registering and renting a factory is not large, it is just an investment in equipment. It's best to visit other people's factories and equipment.

The machines that make high-end home furnishings are imported and very expensive. Hehe, I hope the state trail will help you.

First of all, whether it is a cabinet door or a cabinet body, the CNC cutting machine is indispensable, the CNC cutting machine undertakes the task of cutting the plate, pulling the groove, and punching vertical holes.

The CNC cutting machine is mainly divided into a three-process CNC cutting machine, a four-process CNC cutting machine, two spindles + row drilling machining center, disc tool change machining center, disc tool change + row drilling machining center.

The cabinet can be made of three-process and four-process CNC cutting machine, disc tool change + row drilling machining center, two spindles + row drilling machining center.

The cabinet door can be made of three-process and four-process CNC cutting machine, disc tool change Yuanming machining center, disc tool change + row drilling machining center.

If you save a little, three machines are enough. Slicer: Cut the purchased plate into the required size.

Edge banding bright machine: the cut edge needs to be sealed, which is good-looking and damp. Laminator:

The substrates are all medium-density, high-density boards. The furniture needs to be pressed with a decorative layer and a protective film.

Save a little Zen chaos, three machines are enough to fine hairpin saws: used to lower the plate, the size of the requirements of Jinghe Bridge accurate. Edge banding machine: melamine board needs to be edge-banded to accompany the hole machine: make a three-in-one hole.

If you save a little, three machines are enough.

Slicer: Cut the purchased plate into the required size.

Edge banding machine: the cut edge needs to be sealed, which is good-looking and damp.

Laminator: The substrate is medium density, high density board. Furniture needs to be pressed with a decorative layer and a protective film.

The most basic thing is that a sliding table saw is enough. Haha, brand new 8000 yuan, edge banding can be sealed by hand, if there is money of course to buy the edge banding machine, manual more than 8000, semi-automatic 3W more, fully automatic 7W more, I said are the cheapest, buy the edge banding machine to buy air compressor, because the edge banding machine to use gas, and then is the row of drilling, 2W up, and then what you need is an open hole row drill, hundreds of dollars, and then if you may do modeling to buy a gong machine, the gong machine can be determined after the factory to see the order. If you want to buy an aluminum cutting machine, the ordinary one is also a few hundred yuan, because you will often cut aluminum.

Then there is the vacuum cleaner, more than 1,000 pieces, depending on the power. A rudimentary panel furniture factory is these equipment, the main material that can be processed is melamine veneer, if you make a small paint house you can do paint, but you also need to add paint equipment, cold press machine is also more expensive, but you can do a small amount of fireproof board, manual paste, paste with more than 50 boards for 48 hours, the same can be used. Lamination should have a professional laminating machine, which is not recommended.

A basic panel furniture factory starts from 0, you can rent a factory building of about 300 to 400 square meters, and you can start with 10W blocks of small equipment and some basic materials.

Four-process cutting machine, side hole machine, edge banding machine Laminating machine is a more commonly used complete set of panel furniture CNC equipment.

If you save a little, three machines are enough for fine saws: they are used to lower the plates, and the dimensions are required to be precise. Edge banding machine: melamine board needs edge banding hole rowing machine: punch three-in-one holes.