How to install the toilet properly

How to install a toilet at home.

Detailed steps for toilet installation.

1. Check the leveling between the sewage pipe and the ground.

It is necessary to check whether there is any blockage of sediment, waste paper and other debris in the sewage pipe, and at the same time, it is also necessary to check whether the ground is level before and after the toilet is installed, and the unevenness needs to be leveled.

2. Determine the center of the sewage pipe.

The method of confirming the center of the sewage pipe is very simple, that is, turn the toilet over, and then draw a simple cross center line at the center of the toilet outlet, and pay attention to the lower cross center line to extend to the bottom of the toilet and the feet around it.

3. Fix the toilet.

First align the toilet with the cross line of the floor sewage opening, ensure that the toilet is installed horizontally and then press the seal tightly, and the next step is to install the screws and decorative caps of the feet to fix the toilet.

4. The bottom is sealed.

After fixing the toilet, it is necessary to install a special sealing ring at the sewage outlet, or apply a circle of glass glue (putty) or cement mortar around it, and the ratio of cement to sand is recommended to be 1:3.

5. Install the water tank accessories.

Rinse the pipes with water for 3-5 minutes. After ensuring the cleanliness of the tap water, the angle valve and the connecting hose are installed, and then the hose is connected to the installed water tank fittings.

6. Debugging and inspection.

The last step is to inspect the old toilet shed, check whether the location of the drainage valve is flexible, whether the inlet valve is sealed normally, whether there is jamming and leakage, pay attention to see if the inlet valve is equipped with a filtration device, etc., if not, it is recommended to install.

Prepare materials: toilet, angle grinder, glass glue gun, screwdriver, wrench.

1. Use an angle grinder to remove the extra sewage pipe.

2. In general, the sewage pipe should be cut to the extent that it is leveled with the ground.

3. After the sewage pipe is cut, move the toilet to the top of the sewage pipe and align it with the sewage pipe.

4. Turn over the base of the toilet, then put on the sealing ring, then align the sewage pipe, and put the toilet again.

6. After fixing the toilet, install the toilet lid.

7. Finally, use a hose to connect the water inlet valve with the toilet tank.

8. Done.

Step 1 Before the toilet is installed, a comprehensive inspection of the sewage pipe should be carried out to see if there is any mud, sand, waste paper and other debris in the pipe.

At the same time, it should also be checked whether the ground of the toilet installation position is horizontal, and if the ground is found to be uneven, the ground should be leveled.

Step 2 Flip the toilet bowl and determine the center on the toilet drain.

At the same time, draw a cross centerline, which should extend to the bottom of the toilet bowl around the feet.

Step 3 Align the reticle line on the toilet bowl with the ground drain outlet and install the toilet bowl horizontally.

At the same time, press the sealing ring tightly and install the anchor screws and decorative caps.

Step 4 Install a special sealing ring on the toilet drain.

Step 5 Drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes.

Then install the angle valve and connecting hose.

Then connect the hose with the installed tank fitting inlet valve and press the water source.

Step 6 Check whether the water inlet and sealing of the water inlet valve are normal.

Check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and whether there is leakage to install the filter device of the inlet valve.

Accessories: 1 pair of plastic bearings, 1 pair of screws, 1 pair of lower lock gaskets, 1 pair of lower lock bolts, 1 pair of decorative covers.

Step 2: Put the screws on the plastic bracket and place them on the mounting holes of the toilet;

Step 3: Put the washer on the plastic nut, on the one hand, press and hold the top of the screw, turn the nut on the screw from the bottom of the toilet bucket to 9, so that the bracket can also be slightly looser, the screw is longer, and it must be rotated for a period of time;

Step 4: Two small holes in the toilet lid are aligned with the support column and inserted vertically. Adjust the toilet lid plate on the front, back, and left so that it fits the toilet bowl perfectly. The sides are then bolted and locked in hand so that the support does not move.

Step 5: Open the toilet cover, press the front button of the toilet cover, remove the cover vertically, and use a screwdriver to strengthen the screws so that they are fully tightened;

Step 6: Place the stainless steel decorative toilet lid on the stand.

Step 7: Replace the cover again and check whether the deceleration function of the toilet cover is normal and complete. That is, the installation of the entire toilet lid is completed.

30 to 40 cm.

Ask how many millimeters from the floor tile should the drain pipe butted to the toilet dove?

Answer: There is a sealing ring at the bottom of the toilet drain, and the source sealing ring is put on the sewage pipe just to dock with the toilet outlet. Therefore, when installed on site, the sewer nozzle is about 1cm from the ground.

Question: I disagree with the installer, whether the installer generally cuts the drain pipe and the floor tile flat bundle to install the toilet correctly.

Installation process:

Before installing the toilet, the sewage pipeline should be comprehensively inspected to see if there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal.

Determine the center of the sewage pipe and draw a cross centerline.

Flip the toilet, center it on the toilet drain, and draw a cross center line, which should extend to the bottom of the toilet around the feet.

If there is a screw installation position at the bottom foot of the toilet, it is recommended not to use it, one is to destroy the waterproof layer, and the other is to fear that it will crack the toilet if it is tight.

Install a special sealing ring on the toilet drain.

Align the cross line on the toilet with the cross line of the ground sewage outlet, install the toilet, and press the sealing ring tightly, and then put a circle of glass glue around the bottom of the toilet, and the toilet installation should be kept at the front and back left and right level.

Install or debug the tank fittings. Check the water pipes first, drain the water for 3 5 minutes to rinse the pipes to ensure the cleanliness of the water pipes; Then install the angle valve and the connecting hose, then connect the hose with the installed water tank accessories inlet valve and press the water source, check whether the water inlet and sealing of the inlet valve are normal, check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and check whether there is leakage and install the inlet valve filtration device.

After the toilet is installed, it should wait until the glass glue has cured before it can be used with water, and the curing time is generally 24 hours.

Precautions: 1) When installing the toilet, please do not pour cement mortar into the cavity in front of the toilet or other cavities, so as not to crack the toilet feet due to cement condensation and expansion.

2) When using the toilet, please do not flush newsprint, diaper pads, toilet napkins and other easily clogged items into the toilet.

3) The toilet should not be used in a sub-zero temperature Celsius water environment, otherwise the water will freeze and expand and crush the ceramic.

4) To prevent breakage and water leakage, please do not hit the ceramic with hard objects.

5) In order to keep the surface of the product clean, please clean it with a nylon brush and soapy water or neutral detergent, and it is strictly forbidden to clean it with a steel brush and a strong organic solution, so as not to damage the glaze of the product and erode the pipeline.