After the toilet is flushed, it keeps flowing, what is the reason

1. Whether there are cracks in the toilet water tank. If there is a problem with the burning of the toilet, cracks may appear, causing the toilet tank to leak. Although it can be used with proper repairs, it is advisable to replace the toilet bowl as it may leak after repairs.

2. The aging of the internal parts of the water tank may also lead to the leakage of the toilet water tank. Open the toilet tank lid and inspect it carefully. For example, the drain switch is sometimes pressed but fails to pop out.

At this point, the parts can basically be replaced. There is no need to replace the toilet.

3. If there is no leakage in the toilet tank, you can check whether the sewer is in good condition. Leaks at the lower part of the toilet tank and the connection of the water pipe are also common, so it is important to double-check that the connection is intact.

4. The toilet float is also an important component that needs to be checked. The water float determines the water level of the toilet tank. If there is no problem with the water float, the toilet tank will still flow after it is full, causing a water leak.

If there is a problem with the water float, you can choose to replace it. You can buy one online for a few dozen dollars, but you should also choose based on your toilet model.

5. The leakage of the flush toilet may also be due to the problem of the sewer pipe below. It is a pipe that transports water mainly to the toilet tank, and it is very likely here.

The reason why the toilet does not stop flowing after use is that the plastic gasket on the outlet hole of the pumping system is aging and elastic enough to be sealed. Solution: 1. Whether the black semi-circular float on the overboard assembly is properly covered, or the black semi-circular float falls off, or the rope is stuck or the black semi-circular float is deformed; 2. The single toilet downspout component is shaken by hand, if it shakes, it means that the semicircular fixing piece at the bottom of the downspout component is broken or loose.

Start by pressing the drain button to see if the flow can stop.

If it doesn't work, then you need to open the water tank cover, check whether the water tank cover button and the button on the drain valve can easily pop up, if there is a card or a light press to the end, it is a problem with the water tank button or water button.

The key switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored.

Solution: Quickly press and release the key switch, preferably twice or more in a row, until the key switch returns to its usual strength, and the switch can be reset after repeating it a few times.

After treatment, the sound of water storage in the water tank is getting smaller and smaller, which means that the water tank has been restored, and when the water is full, there will be no more water in the toilet.

The next time you encounter this situation, you can follow the above methods.

In addition, every time you use the water tank, try to press the button that will not get stuck to reduce the leakage of jamming.

The toilet still runs after flushing, which means that the toilet is broken, and the water tank part of the water should not be connected well, so it should be repaired quickly, otherwise it will be a great waste of water bills.

For a leaky toilet in the back row, it is possible that the float in the tank is not buoyant enough. Nowadays, many toilet tanks are small, which can save water, but the shortcomings are also obvious, that is, the buoyancy of the float is not enough, so that the float can not turn off the inlet valve after being flooded, so it leaks. To change the float, you can consult the manufacturer for what pressure float to choose.

The toilet bowl still runs after flushing, so there must be a problem with the inlet valve and it must be repaired. Easy to use.

In this case, you can try to flush the water again, hold it and wait a few seconds before sending it, if it still doesn't work, it means that your toilet, that is, the parts in the tank, is faulty, and he has no way to stop the water, so it keeps running. Replace it with a new one and reinstall it.

The key switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored.

Solution: Quickly press and release the key switch, preferably twice or more in a row, until the key switch returns to its usual strength, and the switch can be reset after repeating it a few times.

After treatment, the sound of water storage in the water tank is getting smaller and smaller, which means that the water tank has been restored, and when the water is full, there will be no more water in the toilet.

The next time you encounter this situation, you can follow the above methods.

In addition, every time you use the water tank, try to press the button that will not get stuck to reduce the leakage of jamming.

Your water level is set too high, and the water will flow out of the toilet if it goes through the overflow hole next to the drain valve. Rotate the screw of the inlet valve counterclockwise to lower the water level, and the water will not pass through the overflow hole after the water is loaded, and it will be fine.

If there is a problem with the burning of the toilet, cracks may appear, causing the toilet tank to leak. Although it can be used with proper repairs, it is advisable to replace the toilet bowl as it may leak after repairs.

The reason why the toilet does not stop flowing after use is that the plastic gasket on the outlet hole of the pumping system is aging and not elastic enough to be sealed.

Solution: 1. Whether the black semi-circular float on the overboard assembly is properly covered, or the black semi-circular float falls off the side, or the rope is stuck or the black semi-circular float is deformed;

2. The cavity of the single toilet downfall component is shaken by hand, if it is shaken, it means that the semicircular fixing piece at the bottom of the downwater component is broken or loose.

The water in the water tank, if the pipe full of the downwater assembly flows out, it is necessary to check the water inlet assembly: there is an adjusting screw on the water inlet assembly, which is used to adjust the water level. Try to tighten it first, if not, it may be that the water-stopping core (or water-stop film) in the water inlet assembly needs to be replaced.

3. The water stop is generally sold in the wholesale market of household appliances in the city, and the whole set of flushing equipment is generally sold in the plumbing equipment store of the hardware store, which is simple to replace, and can generally be replaced by itself or the merchant can replace it on behalf of the merchant.

What to do if the toilet tank keeps running water.

It is the float valve that does not return, causing the make-up pipe to fail to close. Open the lid and adjust the float (manual adjustment). There is a plug in the water tank, which is connected to the floating iron ball, press down and pull the plug up, or it will continue to run if you don't put it down, open the lid of the water tank, and press the plug down with your hand.

The drain in the toilet tank is leaking and needs to be replaced.

It is the float valve that does not return, causing the make-up pipe to fail to close. Open the lid and adjust the float. There is a plug in the water tank, which is connected to the floating iron ball, press down and pull the plug up, or it will continue to run if you don't put it down, open the lid of the water tank, and press the plug down with your hand.

A toilet, also called a toilet, is a bucket with a lid for urinating and urinating. The invention of the toilet is known as a great invention, which solved the problem of people eating and drinking in and out of Lazar. Later, it evolved into a flush toilet using the principles of siphon, spiral siphon, and now the latest jet siphon and superspin siphon.

There are also people who believe that the flush toilet is the root of all evil because it consumes a lot of domestic water. There are many classifications of toilets, including split and conjoined. With the development of science and technology, many novel varieties have also appeared.

According to the matching method of the toilet seat, it can also be divided into ordinary toilet and smart toilet. Smart toilets can also be further divided into automatic set change smart toilets and non-automatic set change toilets, the former includes automatic set change plus flushing, automatic change set with flushing and drying and other different types.

The history of the toilet can be traced back to the Han Dynasty, when the toilet was called Huzi, which was dedicated to the emperor, and legend has it that it was made of jade. It was held by eunuchs who served the emperor at any time. Later, in the Tang Dynasty, because there was a person named Li Hu in the emperor's family, in order to avoid secrecy, he changed the name of Huzi to Beast or Mazi.

After that, in the circulation, it evolved into the name of the toilet.

What are the main causes of toilet leakage? Please introduce it below!

1. Reasons for toilet leakage

1. The seal of the toilet is not done well when it is installed

The toilet flange is not installed or the flange is aging and cracked, and the toilet flange is mainly used to seal and prevent leaks.

2. The toilet may not be installed properly when it is installed:

As a result, the sewage outlet on the ground is not aligned with the toilet drain diameter, and the dirty water will leak out. It's easyThe toilet is leaking The occurrence of the situation.

3. Loosening of the toilet part:

Caused by long-term use, the toilet bowl and the ground are loose and leaking.

4. The problem of aging toilet tank:

After the toilet tank is used for a long time, there will be the problem of aging, and clean water will flow out.

5. The problem of aging toilets:

After the toilet is used for a long time, there will be the problem of toilet aging, and the internal ceramic cracks will burst and expand.

6. Toilet inlet and outlet group:

There may be a problem with the toilet inlet and outlet group.

2. Repair the leakage at the bottom of the toilet in the bathroom

1. Judge the water quality of the toilet

If it's clear water, it's a problem with the tank. Dirty water requires a toilet flange.

2. Open the water tank of the toilet

First look at what level the internal buoy is at when the tank is full. If the water inside is full and the tank is still flooding, it will definitely leak.

Check the toilet tank for impact cracks

If the internal equipment is fine, also check the toilet tank for impact cracking.

4. Remove the buoy and clean it

If you won't disassemble it, pour in a little dish soap, continue to use it if you can, and replace it if it doesn't.

5. Inspection Is there a problem with the buoy.

Use water to pull the buoy up and down to see if the buoy is sensitive. If it's hard to move, there's a problem with the buoy.

6. Check the outside of the toilet tank

The stainless steel hose interface of the water tank, whether it is tightened or not; Or the internal rubber pads are aging.

You can now check your toilet bowl for these problems, and it is recommended to ask a professional repairer to help you repair the toilet. That's all for thatThe toilet is leaking ——[Article Recommendation]——

Bathroom waterproofing|Is there a leak around the toilet at home? The waterproof step has to be redone!

Toilet partition decoration|From size to accessories to installation, decoration strategies can be referred to.

Precautions for the decoration of sanitary partitions The size selection of sanitary partitions.

Waterproofing measures are very important How to do a good job of waterproofing construction in the bathroom.