-
The elastic spring plug of the bathroom basin is pressed down and does not bounce back to solve the problem as follows:
1. You pour in a little soapy water, wait for 5 minutes to lubricate a version, and shake the high-frequency weight of the low range of spring racing.
2. You can knock down hard objects with small contact surfaces such as screwdrivers at different angles.
3. Suck the stopper of the sink with a suction cup and pull it out vigorously.
4. There is a U-shaped pipe under the sink, remove the U-shaped pipe, take a stick from below and poke it out, and then connect the U-shaped pipe, and prompt that if there is a bad place, then replace it with a new one, and it is best to wrap it tightly with a raw material belt to prevent water leakage.
5。Boil a pot of boiling water, pour it into a basin, soak the spring plug and the surrounding contact surface with heat expansion and cold contraction for 5 minutes, and beat the spring plug on the same side several times with chopsticks.
-
The workaround of not coming back is as follows:
You can knock things down with things at different angles.
Suck the stopper of the sink with a suction cup and pull it out vigorously.
There is a U-shaped pipe under the sink, remove the U-shaped pipe, take it out from below with a stick, and then connect the U-shaped pipe, if there is a bad place, then replace it with a new one, it is best to wrap it tightly with raw tape to prevent water leakage.
You pour a little soapy water and press it again, lubricate it, and press it with a shake!
-
1. Suction the stopper of the sink with a suction cup and pull it out vigorously.
2. You can knock something down at different angles.
3. There is a U-shaped pipe under the handwashing station, remove the U-shaped pipe, take it out from below with a stick, and then connect the U-shaped pipe, if there is a bad place, then replace it with a new one, it is best to wrap it tightly with raw tape to prevent water leakage.
-
The spring-plug of the basin can be removed.
Attack, you can see that there is a hanging spring inside.
Bai small hook, du it fell from the track groove, in the careful dao dang hang it back into the V-shaped groove on the line, and then look at the pipe below, pull it out to see if there is any hair in it or something, if you can take it down with the basin to see, if the spring is broken, this needs to replace the valve core or change the valve core.
-
If the spring of the bathroom basin can't bounce back when you press it again. You can ask a plumber to fix it.
-
After removing it, you can see that a small hook with a hanging spring has fallen out of the track groove, and it is carefully hung back into the V-shaped groove.
version. Maybe the right is stuck, see if there is a hair or something in the pipe pulled out below, if you can take down the basin to take a look, it is estimated that the spring is broken and it will be troublesome, and it is not easy to change.
When combing your hair, you must not get the hair into it, you can't flush it down at all, it will only be blocked inside.
-
You can take a little bit of something and pick it out, and then you can replace it with one if it is sold in the hardware store.
-
Maybe it's stuck, right? Look at the tube below to see if there is a hair or something in it, if you can take it down with the basin to see, it is estimated that the spring is in trouble if it is broken, and it is not easy to change. When combing your hair, you must not get the hair into it, you can't flush it down at all, it will only be blocked inside.
-
See if you can buy accessories, if you can't buy it, you can only pry it up and stop using the plug.
-
It should be broken! Or something stuck on it. You try to a little soapy water in pressing. Lubricate it! Don't die this press, shake and shake it!
-
Buy a new one again, repair it badly, replace it with a new one.
-
The spring plug of the bathroom basin cannot be bounced back when pressed, and the solution is as follows:
You can knock things down with things at different angles.
Suck the stopper of the sink with a suction cup and pull it out vigorously.
There is a U-shaped pipe under the sink, remove the U-shaped dust messy land pipe, take it out from below with a stick, and then connect the U-shaped pipe, if there is a bad place, then replace it with a new one, it is best to wrap it tightly with raw tape to prevent water leakage.
You pour a little soapy water and press it again, lubricate it, and press it with a shake!
-
Boil a pot of boiling water, pour it into a basin, soak the spring plug and the surrounding contact surface with heat expansion and cold contraction for 5 minutes, and beat the spring plug on the same side several times with chopsticks.
-
If this happens, it should be that the spring is broken, you can go back to the basin to buy a new one, and you can install it, it's very simple.
-
You pour in a little soapy water, wait 5 minutes for it to lubricate, and shake the high frequency and low range of the spring race. 2. You can knock down hard objects with small contact surfaces such as screwdrivers at different angles. 3. Suck the stopper of the sink with a suction cup and pull it out vigorously.
4. There is a U-shaped pipe under the sink, remove the U-shaped pipe, take a stick from below and poke it out, and then connect the U-shaped pipe, and prompt that if there is a bad place, then replace it with a new one, and it is best to wrap it tightly with a raw material belt to prevent water leakage. 5。Boil a pot of boiling water, pour it into a basin, soak the spring plug and the surrounding contact surface with heat expansion and cold contraction for 5 minutes, and beat the spring plug on the same side several times with chopsticks.
-
In the bathroom, the spring plug can't be pressed and can't bounce back, what should I do, that is, there is a problem with the button, and you should find a professional to repair it for you.
-
The spring plug of the bathroom basin cannot be bounced back when pressed, and the solution is as follows:
1. You pour in a little soapy water, wait for 5 minutes to lubricate, and shake the high frequency and low amplitude of the spring race.
2. You can knock down hard objects with small contact surfaces such as screwdrivers at different angles.
3. Suck the plug of the sink with a suction cup and pull it hard to come out.
4. There is a U-shaped pipe under the sink, remove the U-shaped pipe, take a stick from below and poke it out, and then connect the U-shaped pipe, and prompt that if there is a bad place, then replace it with a new one, and it is best to wrap it tightly with a raw material belt to prevent water leakage.
5。Boil a pot of boiling water, pour it into a basin, soak the spring plug and the surrounding contact surface with heat expansion and cold contraction for 5 minutes, and beat the spring plug on the same side several times with chopsticks.
If you want to save trouble, you can just put the drainage hose in the squatting urinal, there is no other way. >>>More
This can't be generalized, some mirrors are big, some are small, some mirrors are horizontal, some are vertical, there is a big difference, but there is a general standard, that is, the height of your family, more than ten centimeters taller than the tallest person is more appropriate.
There is no clear regulation on the size of bathroom basins, because there are many styles and shapes of washbasin products nowadays. And everyone has different living habits and uses different products, so the sizes of products launched by merchants are also different. The usual common sizes are: >>>More
It depends on what type of pot you buy, and the quality of the material varies greatly, and there are countertop basins and undercounter basins. The oldest undercounter basin (oval, commonly used in hotels in the past) is only a few dozen dollars.
It doesn't look like a heat exchanger, it's an ordinary radiator, right?! The heat exchanger should be packaged as a whole, so that the hot water is wrapped in the inner tap water copper tube to achieve the purpose of heating.